Irrigation methods are usually sorted by how the water reaches the soil. It can flow over the surface, spray through the air like rain, drip at the base of the plant, or seep in from below. Farm textbooks list dozens of variations. For gardens and small plots, eight types cover almost everything you’re likely to use. Below is what each one is, where it works, and where it falls short.
How garden irrigation systems are grouped
- Surface: water flows over or across the ground by gravity.
- Sprinkler (overhead): water is pressurised and thrown through the air.
- Micro or localised: small amounts of water go straight to the root zone, through drippers, porous pipe or tiny sprayers.
- Sub-irrigation: water is released below the surface or drawn up from a reservoir.
Efficiency generally rises as you move from surface methods towards drip and sub-irrigation, because less water is lost to evaporation, wind and runoff. For more on that, see what is the least efficient irrigation system.
The 8 types
1. Surface irrigation (basin and furrow)
Water runs into shallow channels between rows (furrows) or into small dished areas around plants (basins). It’s the oldest method and still common on farms.
- Good for: potatoes, squash or sweetcorn in rows on level ground, and tree basins.
- Drawbacks: a lot of water soaks past the roots or evaporates, and it doesn’t work well on slopes or sandy soil.
2. Hand watering (can or hose)
It’s not a “system” in the engineering sense, but it’s still how most gardens get watered.
- Good for: containers, seedlings, spot-watering new plants, small gardens.
- Drawbacks: it takes time and you have to be there. It’s also easy to water too shallowly, wetting the surface while the deeper soil stays dry.
3. Hose-end sprinklers
Oscillating, rotating, impulse and stationary sprinklers that sit on the lawn and connect to a hose.
- Good for: lawns, newly seeded areas, broad beds of low plants.
- Drawbacks: wind drift and evaporation, wet foliage, and coverage that often overlaps unevenly. They can also be restricted during hosepipe bans.
4. In-ground (pop-up) sprinklers
Fixed spray heads, rotary nozzles and rotors fed by buried pipe and controlled by valves and a timer. See the different types of sprinkler heads.
- Good for: lawns, where they give even, automated coverage.
- Drawbacks: higher cost and installation effort, and coverage depends on careful head spacing.
5. Drip irrigation
Polyethylene tubing carries water to emitters that release a set flow, often a few litres per hour. Water can come from separate drippers punched into the pipe or from inline dripline with the emitters built in.
- Good for: vegetable beds, borders, shrubs, containers, greenhouses.
- Drawbacks: emitters can clog without a filter, and the tubing needs some planning and occasional checks.
6. Soaker and leaky hose
Porous hose made from recycled rubber or fabric that “sweats” water along its whole length. It’s covered in detail in leaky hose and soaker hose garden irrigation.
- Good for: straight rows, hedges, densely planted beds.
- Drawbacks: output varies along the length and with pressure, and it tends to have a shorter working life than drip tubing.
7. Micro-sprinklers, sprayers and misters
Small heads on stakes, fed by drip tubing, that spray a fine fan or circle over a small area.
- Good for: ground cover, closely spaced seedlings, propagation areas, and greenhouses where you want humidity.
- Drawbacks: more evaporation than drip, and they wet the foliage.
8. Sub-irrigation (ollas, wicking and subsurface drip)
Water is released underground or drawn up by capillary action. Unglazed clay pots (ollas) are buried and filled. Self-watering containers and wicking beds draw water from a reservoir. Subsurface drip lines are buried in the root zone.
- Good for: containers, raised beds, hot dry climates, holidays.
- Drawbacks: it’s hard to see if it’s working. Buried lines can be damaged by digging or invaded by roots, and ollas only water a small radius.
Comparison table
| Type | Water efficiency | Set-up cost | Effort to run | Best fit |
|---|---|---|---|---|
| Surface (basin and furrow) | Low | Very low | Moderate | Row crops on flat ground |
| Hand watering | Variable | Very low | High | Pots, seedlings |
| Hose-end sprinkler | Low to moderate | Low | Moderate | Lawns |
| In-ground sprinkler | Moderate | High | Low once set up | Lawns |
| Drip | High | Low to moderate | Low | Beds, borders, pots |
| Soaker or leaky hose | Moderate to high | Low | Low | Rows, hedges |
| Micro-sprinkler | Moderate | Low | Low | Ground cover, propagation |
| Sub-irrigation | High | Low to moderate | Low | Pots, raised beds |
These ratings are general. A carefully run sprinkler system can beat a badly designed drip system.
Alternatives to a micro drip system
Micro drip, with 4 mm tube and individual drippers, suits containers and mixed planting, but some people find the small fittings fiddly or the clogging annoying. Alternatives include:
- Inline dripline (16 mm with built-in emitters): fewer separate parts and less to come loose. It suits rows and beds.
- Soaker or leaky hose: the simplest to lay. You just snake it through the bed and connect a hose.
- Micro-sprinklers: better for dense ground cover where individual drippers would be impractical.
- Ollas or buried bottles: no tubing at all. Good for a few high-value plants or for gravity setups on an allotment.
- Self-watering containers and capillary matting: for pots and greenhouses, especially while you’re away.
The types of micro irrigation goes into each localised option in more depth.
How to choose
Start from the plants and the water supply, not the hardware. Lawns generally need overhead coverage. Beds, borders and containers usually do better with drip or porous hose. Low-pressure sources like water butts suit gravity drip or ollas better than sprinklers. Our garden irrigation planning guide works through these decisions step by step, and irrigation system components explains the parts each type needs.