To connect a garden irrigation system to an outdoor tap, screw on a short chain of fittings, known as the head assembly, in this order: backflow protection, timer, filter, pressure regulator, then an adaptor to your drip tubing or hose. Each part does a different job. Getting the order and the thread types right is what prevents leaks, clogged drippers and fittings blowing off.
The order of fittings
| Order | Part | Why it’s there |
|---|---|---|
| 1 | Outdoor tap | The water source |
| 2 | Backflow preventer (check valve or vacuum breaker) | Protects the drinking supply. Often built into newer taps |
| 3 | Timer (optional) | Turns water on and off on a schedule |
| 4 | Filter | Catches grit before it reaches drippers |
| 5 | Pressure regulator | Lowers mains pressure to suit drip tubing |
| 6 | Tubing adaptor | Connects to your 13–16 mm drip tube, or to a hose connector |
Putting the timer before the filter and regulator means they aren’t held under full mains pressure all the time. They’re only pressurised while the timer is open. Some kits combine the filter and regulator into one unit. Follow the manufacturer’s order if it differs.
Check your tap thread first
Thread mismatches cause many of the leaks at the tap.
- UK and much of Europe: outdoor taps usually have a 3/4 inch BSP (British Standard Pipe) male thread, though 1/2 inch taps exist.
- US and Canada: outdoor spigots use garden hose thread (GHT), 3/4 inch.
BSP and GHT look similar but aren’t compatible. A fitting may screw on partway and then leak or cross-thread. Buy timers and adaptors made for your country’s standard, or use the correct converter.
Many UK taps also accept a plastic threaded tap connector for snap-on hose fittings. These are convenient, but check that the connector suits your timer before you buy.
Step-by-step connection
- Check the tap. It should turn fully on and off without dripping. Note whether it has a built-in double check valve; on UK taps, this is often marked.
- Fit backflow protection if the tap doesn’t have it. Screw it on hand-tight, with its washer in place. See do you need a backflow preventer for garden irrigation.
- Fit the timer, with fresh batteries. Hand-tighten only. Overtightening plastic threads can crack them.
- Add the filter, making sure the flow arrow points away from the tap.
- Add the pressure regulator, again checking the flow arrow. Choose one rated for your tubing.
- Attach the tubing adaptor and push your drip supply tube onto it. Warm, stiff tube in hot water first so it slides on more easily.
- Support the weight. A full head assembly can be heavy enough to strain the tap. A bracket or a short flexible hose section helps.
- Turn the tap on slowly and check every joint for drips.
- Flush the system with the line ends open, then close them.
Keeping the tap free for a hose
A two-way (Y) splitter with individual shut-offs, fitted straight after the backflow device, lets you run the irrigation from one outlet and a normal hose from the other. Two-outlet timers can also run two separate irrigation zones from one tap. See how to divide your garden into irrigation zones.
Connecting soaker hose or sprinklers instead of drip
- Soaker/leaky hose: use the same head assembly, but swap the drip adaptor for a hose connector. A pressure reducer or flow washer is still usually recommended. See leaky hose and soaker hose garden irrigation.
- Hose-end sprinklers: backflow device and timer, then a hose. A pressure regulator generally isn’t needed, as sprinklers need higher pressure.
- Buried sprinkler systems: these usually connect to the supply pipe rather than an outdoor tap, often with a dedicated backflow assembly. See how to install pop-up sprinklers in an existing lawn.
If you don’t have an outdoor tap
Fitting a new outdoor tap is a common plumbing job, but it connects to the drinking supply, so it must meet local water regulations, including backflow protection. Many people use a plumber. Alternatively, run the system from a water butt: building a PVC rainwater harvesting system explains the gravity and pump options.
Fixing leaks at the tap
| Symptom | Likely cause | Fix |
|---|---|---|
| Drips where the fitting meets the tap | Missing or worn washer, or a thread mismatch | Fit a new washer; check BSP/GHT compatibility |
| Spraying from a cracked part | Overtightened plastic or frost damage | Replace the part, hand-tighten only |
| Leak at the push-fit tube connection | Tube not pushed fully home, or cut at an angle | Recut square, warm the tube, push fully on |
| Timer not opening | Flat batteries, or a debris-blocked valve | Replace batteries; clean the inlet screen |
| Weak flow at the drippers | Clogged filter, or tap only partly open | Clean the filter; open the tap fully |
A note on PTFE tape: it’s for sealing tapered pipe threads. Most hose and timer connections seal on a rubber washer instead, so adding tape there usually doesn’t help and can stop the washer seating properly.
Winter care
In frost-prone areas, remove the timer, filter and regulator before the first hard frost and store them indoors. If your outdoor tap has an internal isolating valve, turn it off and drain the tap. Water left in the head assembly can freeze and split it.
For the bigger picture of planning a system before you connect it, see planning a garden irrigation system.