Installing pop-up sprinklers in an established lawn is a bigger job than laying drip in a border, but it’s achievable for a careful DIYer. The aim is to get the pipe in with as little damage to the turf as possible, and to set every head at the right spacing and height so the lawn is watered evenly. This guide covers the job in order, from planning to programming the controller.
Before you start: is this a DIY job?
Consider getting professional help for some or all of the work if:
- Local rules require a licensed installer or a tested backflow device on the mains connection
- You’re unsure about buried services, such as gas, electricity, water or telecoms
- The lawn is large, steeply sloped or full of tree roots
- You’re not comfortable with plumbing or low-voltage wiring
A common compromise is to do the digging, pipe-laying and heads yourself, and pay a plumber for the mains connection and backflow device. See do you need a backflow preventer for garden irrigation.
Plan the layout and zones
Good planning matters more than anything else here.
- Measure the lawn and draw it to scale.
- Measure flow and pressure at the supply point. See planning a garden irrigation system.
- Choose head types: fixed sprays or rotary nozzles for smaller lawns, rotors for larger ones. See the different types of sprinkler heads.
- Space heads head-to-head, with corners first, then edges, then the middle. See sprinkler head spacing.
- Divide heads into zones your supply can run. See how to divide your garden into irrigation zones.
- Decide where the valves and controller will go. Valves usually sit in a valve box near the supply. The controller goes in a garage, a shed or a weatherproof outdoor spot near a power supply.
Some manufacturers and retailers offer layout design help if you send them measurements.
Tools and materials
- Spade, half-moon edger or turf cutter (hire)
- Trenching spade, or a hired trencher or vibratory plough for larger lawns
- Polyethylene or PVC pipe and fittings suited to your system
- A pipe cutter (not a saw)
- Pop-up heads and nozzles
- Swing pipe (flexible “funny pipe”) and fittings for connecting heads
- Valves, valve box and controller
- Direct-burial waterproof wire connectors, and irrigation wire
- Duct tape or caps for pipe ends
- Tarps or sheets for spoil
Step-by-step installation
1. Locate buried services
Before digging, find out what’s underground. In the US, contact 811 a few days before you dig. Elsewhere, check utility plans, ask your providers, and consider hiring a cable locator. Hand-dig near any known service, and around trees.
2. Mark head positions and trench lines
Use marking paint, flags or pegs and string to mark each head and the trench routes between them and back to the valves. Keep trenches as straight as practical.
3. Lift the turf
Cut the turf in narrow strips along each trench line and lift it with a spade or turf cutter. Roll or stack it on a sheet in the shade and keep it moist so it can be relaid within a day or two. Put soil on a separate sheet so the lawn stays clean.
4. Dig the trenches
Dig to the depth recommended for your pipe and climate. Many residential systems bury lateral pipe somewhere around 15–30 cm (6–12 in) deep, with mainlines often deeper. Check local practice, especially where the ground freezes. A hired trencher or vibratory plough is much faster on larger lawns. Bore or tunnel under paths rather than lifting them.
5. Install valves and manifold
Set the valve manifold in its box at the supply end, on a gravel base for drainage. Connect it to the supply through the backflow device required in your area.
6. Lay the pipe
- Cut pipe with a proper cutter, because saws leave shavings that block nozzles.
- Keep ends taped or capped so soil and debris stay out.
- Make joints according to the manufacturer’s method (clamps, compression or solvent weld).
- On pressurised mainlines, extra care with joints pays off, because leaks there run constantly.
- Cut out kinks and join with a coupler rather than trying to straighten them.
7. Flush the lines
Before fitting any nozzles, turn on each zone with the head fittings open and let water run until it’s clear. This flushes out soil and debris that would otherwise block the nozzles on day one.
8. Fit heads on swing pipe
Connect each head to the lateral with a short length of swing pipe rather than a rigid riser. The flexible link makes it easier to set the head in exactly the right place and height, and it lets the head move slightly if it’s driven over or shifted by frost, instead of cracking a fitting.
9. Set the head height
Set each head so its top sits flush with the soil surface, not raised above it, and vertical. Heads set too high get hit by mowers. Heads set too low get buried by thatch and grass. A pop-up height of around 10 cm (4 in) suits many lawns. Taller grass may need a taller pop-up.
10. Test and adjust before backfilling
Run each zone, then:
- Check that each head pops up fully
- Adjust the arc so water stays on the lawn
- Adjust the radius so each spray reaches the next head
- Look for leaks at every joint
11. Backfill and relay turf
Backfill around the pipes with fine soil (no sharp stones against the pipe), firming it in layers to limit settling. Relay the turf strips, press them down, and water them well. Top up any dips that appear over the next few weeks.
12. Wire and program the controller
Run irrigation wire from each valve to the controller, using direct-burial waterproof connectors at the valves. Program each zone with a run time based on its head type. Rotors need longer than sprays. A catch-cup test, described in sprinkler head spacing, shows how much each zone actually applies.
Best time of year to do it
Spring or early autumn is usually easiest. The soil is workable, and the turf recovers quickly when relaid. Avoid very dry, hard ground and waterlogged or frozen soil.
Common mistakes
- Skipping the flush, so nozzles block immediately.
- Cutting pipe with a saw, which leaves shavings.
- Connecting heads directly to rigid pipe with no swing joint.
- Setting heads above grade, where mowers hit them.
- Mixing sprays and rotors on one zone.
- Spacing heads too far apart, leaving dry rings.
- Not planning for winter: in frost-prone areas, buried systems need draining or blowing out before freezing weather.
For an idea of budget before you start, see how much a garden irrigation system costs.