The main types of irrigation sprinkler heads are fixed spray heads, rotary (multi-stream) nozzles, gear-driven rotors, impact rotors and bubblers. They differ in how far they throw water, how fast they apply it (the precipitation rate), and the pressure they need. Fixed sprays suit small lawns and beds. Rotors suit larger open areas. Rotary nozzles sit in between, and bubblers water trees and shrubs at the base. For setups that aren’t buried, there’s also a family of hose-end sprinklers.
In-ground sprinkler heads
Fixed spray heads
These spray a steady fan of water with no moving parts in the nozzle. They’re the most common head in small residential lawns.
- Typical radius: roughly 1.5–4.5 m (5–15 ft).
- Precipitation rate: high, often around 40 mm (1.5 in) per hour or more, so they apply water quickly.
- Patterns: fixed arcs (quarter, half, full circle, strips) or adjustable-arc nozzles.
- Watch out for: runoff on clay or slopes, and misting and drift if pressure is too high.
Rotary (multi-stream) nozzles
These screw onto standard spray bodies but throw several rotating streams instead of a fan.
- Typical radius: roughly 3–9 m (10–30 ft), depending on the model.
- Precipitation rate: much lower than fixed sprays, so water has more time to soak in.
- Good for: upgrading spray zones to reduce runoff, and for slopes and clay soil.
- Note: they need longer run times than the fixed sprays they replace.
Gear-driven rotors
A single stream rotates slowly back and forth, driven by internal gears.
- Typical radius: roughly 6–15 m (20–50 ft), with larger models beyond that.
- Precipitation rate: low, often around 13–25 mm (0.5–1 in) per hour.
- Good for: medium and large lawns.
- Note: they need more pressure than sprays and longer run times.
Impact rotors
The classic “tick-tick-tick” sprinkler. A spring-loaded arm knocks the stream around in steps.
- Typical radius: medium to long. They’re often used on large areas and fields.
- Good for: big open spaces. They’re also more tolerant of slightly dirty water than fine nozzles.
- Note: louder, with more exposed moving parts.
Bubblers
These flood a small basin with a gentle flow rather than spraying.
- Coverage: very small, usually right at the plant.
- Good for: trees, shrubs and planters with basins to hold the water.
- Note: they need level ground or a basin, or the water runs off.
Comparison table
| Head type | Typical radius | Precipitation rate | Typical pressure | Best use |
|---|---|---|---|---|
| Fixed spray | 1.5–4.5 m (5–15 ft) | High | Lower | Small lawns, narrow strips, beds |
| Rotary nozzle | 3–9 m (10–30 ft) | Low | Moderate | Small to medium lawns, slopes, clay |
| Gear-driven rotor | 6–15 m+ (20–50 ft+) | Low | Higher | Medium to large lawns |
| Impact rotor | Medium to long | Low to moderate | Higher | Large areas, fields |
| Bubbler | At the plant | Very high (localised) | Low | Trees, shrubs |
The figures are typical ranges. Always check the manufacturer’s chart for the exact nozzle and pressure you’ll use.
Pop-up heights and body features
In-ground spray and rotor bodies pop up when the zone runs and retract flush with the ground afterwards.
- Pop-up height: common heights include around 5 cm (2 in), 10 cm (4 in), 15 cm (6 in) and 30 cm (12 in). Taller pop-ups clear taller grass or ground cover. A 10 cm pop-up is a common choice for many lawns.
- Pressure-regulated bodies hold the nozzle at its ideal pressure and reduce misting.
- Check valves in the body stop water draining out of the lowest heads after each cycle, which matters on slopes.
- Shrub adaptors and fixed risers raise heads above bed planting.
Hose-end sprinkler types
If you’re not burying pipe, these attach to a hose:
- Oscillating: a bar of holes rocks back and forth, covering a rectangle.
- Impulse/impact: the hose-end version of an impact rotor. Long throw, adjustable arc.
- Rotating: spinning arms throw water in a circle.
- Stationary (spot): a fixed pattern with no moving parts, for small areas.
- Travelling: a sprinkler that moves along the hose. Useful for long lawns.
Hose-end sprinklers are cheap and flexible, but they usually give less even coverage and lose more water to wind and evaporation than a well-designed in-ground system.
Don’t mix head types on one zone
Sprays apply water several times faster than rotors. If both share one valve, the spray-covered area gets soaked while the rotor-covered area stays dry, whatever run time you choose. Keep each zone to one head type, and ideally to matched-precipitation nozzles. See how to divide your garden into irrigation zones.
How to choose
- Small or narrow lawns: fixed sprays or rotary nozzles.
- Large open lawns: rotors.
- Slopes and clay soil: rotary nozzles or rotors, since low application rates reduce runoff.
- Trees and shrubs: bubblers or drip rather than overhead heads.
- Low water pressure: check each head’s minimum pressure. Fixed sprays generally need less than rotors, and fewer heads per zone helps.
Once you’ve chosen heads, spacing them correctly is what makes them work. See sprinkler head spacing for head-to-head coverage and how to install pop-up sprinklers in an existing lawn.