Head-to-head coverage means spacing sprinkler heads so the spray from each one reaches the next head. In practice, that means the distance between heads roughly equals each head’s throw radius. It’s the standard spacing rule for lawn sprinkler systems, because sprinklers apply most of their water close to the head and less towards the edge of their throw. Overlapping patterns this way evens out the total so the whole lawn gets a similar amount.
What head-to-head coverage means
If a spray head throws water 4 m, heads at head-to-head spacing sit about 4 m apart. Each head waters right up to its neighbours, and every patch of lawn gets water from more than one head.
You’ll sometimes hear spacing described as a percentage of the spray’s diameter. Head-to-head is about 50% of diameter, which is the same as 100% of radius. Some guides allow slightly wider spacing in ideal conditions, but head-to-head is the usual target for residential lawns.
Why it matters: the doughnut effect
A single sprinkler doesn’t wet its circle evenly. Output is typically heavier in some bands and lighter towards the outer edge. If heads are spaced too far apart, the light outer edges barely overlap and you get dry rings or patches between heads, often called the “doughnut” effect.
Running the system longer doesn’t fix that. It just overwaters the areas that were already getting enough. The fix is spacing and adjustment.
Square vs triangular spacing
| Pattern | How it’s laid out | Pros | Cons |
|---|---|---|---|
| Square | Heads at the corners of squares, rows lined up | Easy to lay out along straight edges | Slightly less even in the middle of each square |
| Triangular | Rows offset so heads form equilateral triangles | More even coverage, can allow slightly wider spacing | Harder to fit to rectangular edges |
For typical rectangular residential lawns, square spacing with edge-and-corner heads is the most common. Triangular spacing suits large, open, irregular areas.
How to lay out heads, step by step
- Draw the lawn to scale on paper or graph paper, including paths, beds and trees.
- Check the head’s real throw. Use the manufacturer’s chart for your nozzle at your operating pressure. Heads only reach their rated radius at the right pressure.
- Place corner heads first. Use quarter-circle heads in each corner.
- Place edge heads. Run half-circle heads along the edges at a spacing no greater than the throw radius.
- Fill the middle. Add full-circle heads where needed, so that every head’s spray reaches its neighbours.
- Check narrow strips. Side returns and strips are often better served by strip nozzles or drip than by standard heads.
- Group heads into zones based on your flow rate, keeping sprays and rotors separate. See how to divide your garden into irrigation zones.
Adjusting for wind, pressure and odd shapes
- Wind: on windy sites, designers usually space heads closer together than the full radius, because wind distorts the pattern. Lower-angle nozzles or rotary nozzles, which throw heavier streams, can also help.
- Low pressure: heads won’t reach their rated throw. Either use fewer heads per zone so each gets more pressure, choose heads rated for lower pressure, or space them closer.
- High pressure: fixed sprays can mist and drift. Pressure-regulated bodies help.
- Curves and odd shapes: adjustable-arc nozzles let you set any angle. Expect to use more heads than a simple rectangle would need.
- Obstacles: trees and shrubs block spray. Add a head on the far side rather than trying to throw around them.
Matched precipitation
A quarter-circle head spreads water over a quarter of the area a full-circle head covers. If both deliver the same flow, the quarter-circle area gets about four times as much water. Matched precipitation rate nozzles solve this by scaling flow to arc: a half-circle nozzle delivers about half the flow of a full circle, and a quarter about a quarter.
Use matched-precipitation nozzles of the same series within a zone, and keep fixed sprays, rotary nozzles and rotors in separate zones. See the different types of irrigation sprinkler heads.
Testing coverage with a catch-cup test
A catch-cup test (often done with tuna cans or similar straight-sided containers) shows how evenly a zone waters:
- Place 8–12 identical straight-sided containers in a grid across one zone, including near heads and midway between them.
- Run the zone for a fixed time, for example 15 minutes.
- Measure the water depth in each container.
- Compare: big differences show uneven coverage, and the average shows how much water the zone applies per minute.
The result also tells you how long to run each zone to apply the amount of water you want.
Fixing dry spots in an existing system
- Clear grass and soil from around heads that don’t pop up fully.
- Adjust the radius screw so the spray reaches the next head, but not beyond the lawn.
- Check the arc of each head, so it covers the lawn and not the path.
- Clean or replace nozzles that are blocked or worn.
- Check pressure: too many heads on a zone, a leak, or a blocked filter all shorten the throw.
- Add a head if the gap is simply too wide for adjustment to fix.
- Level tilted heads so they spray evenly.
If you’re putting in a new system, read how to install pop-up sprinklers in an existing lawn next.