Planning and System Types

How to Divide Your Garden Into Irrigation Zones

How to split a garden into irrigation zones: measure tap flow, group plants by water need, separate drip from sprinklers, and check each zone's flow against supply.

On this page
  1. What an irrigation zone is
  2. Two reasons to zone
  3. Step 1: Measure your flow
  4. Step 2: Group plants into hydrozones
  5. Step 3: Separate by delivery method
  6. Step 4: Check each zone’s flow against your supply
  7. Step 5: Plan valves and control
  8. Example zone plan for a typical garden
  9. Common zoning mistakes

An irrigation zone is a group of emitters or sprinklers that switch on and off together. Dividing a garden into zones solves two problems at once. Your water supply can only feed so many outlets at a time, and different plants need different amounts of water. Get the zoning right and everything else (timers, run times, even watering) becomes much easier.

What an irrigation zone is

Each zone has its own control point: a manual valve, one outlet on a multi-way tap timer, or a solenoid valve wired to a controller. When that zone runs, every outlet on it gets water. The others stay off. Zones run one after another, so the full supply is available to each in turn.

Two reasons to zone

  1. Hydraulic capacity. If the outlets on one zone together need more water than the tap can supply, pressure drops and the far end of the system barely waters.
  2. Plant needs. Lawns, vegetables, containers and established shrubs need different amounts of water and different schedules. Grouping plants with similar needs is called hydrozoning.

Step 1: Measure your flow

Time how long it takes to fill a bucket from the tap you’ll use, with the tap fully open.

  • 10-litre bucket in 20 seconds = 30 litres per minute = 1,800 litres per hour.
  • In US units: a 5-gallon bucket in 40 seconds = 7.5 gallons per minute.

Many designers don’t plan to use the full measured flow. They leave a margin, often somewhere around 75% of it, to allow for pressure losses and for other taps being used in the house.

Step 2: Group plants into hydrozones

Sort the garden into groups with similar needs:

  • Containers and hanging baskets: frequent, small amounts.
  • Vegetables and fruiting crops: regular, moderate to generous amounts.
  • Lawn: even overhead coverage, deep and infrequent.
  • Mixed borders and new shrubs: moderate.
  • Established shrubs, trees and drought-tolerant plants: occasional deep soaks.

Then refine each group by:

Step 3: Separate by delivery method

Each zone should use one type of outlet:

Step 4: Check each zone’s flow against your supply

Add up the flow of every outlet on the zone, using the same units as your measured supply.

Drip example

  • Supply: 1,800 L/h measured, about 1,350 L/h usable at 75%.
  • Vegetable zone: 60 m of inline dripline with emitters every 30 cm = 200 emitters. At 2 L/h each, that’s 400 L/h. This is well within capacity.
  • Pots zone: 40 drippers at 4 L/h = 160 L/h. This is fine too.

Both could technically run together on capacity. They’re kept separate because pots need watering more often.

Also check the tubing. Most drip tube has a maximum flow and run length recommended by the manufacturer. A zone can be within your tap’s capacity and still exceed what one length of tube can carry, so split long runs or feed them from the middle.

Sprinkler example

  • Supply: 30 L/min measured, about 22 L/min usable.
  • Spray heads used at roughly 4–5 L/min each (check the nozzle chart).
  • 22 ÷ 4.5 ≈ 4 heads per zone at most.
  • A lawn needing 10 heads therefore needs at least 3 zones.

Step 5: Plan valves and control

  • One or two zones: a battery tap timer, with a two-outlet model for two zones.
  • Several drip zones: a manifold with manual ball valves, or a multi-zone battery timer.
  • Sprinkler systems: a valve box with solenoid valves and a mains or Wi-Fi controller.

Label every valve and keep a simple map of which zone covers which area.

Example zone plan for a typical garden

Zone Area Outlet type Typical schedule idea
1 Front lawn Pop-up sprays Deep watering a couple of times a week in dry weather
2 Back lawn Rotors or rotary nozzles As zone 1, longer run time
3 Vegetable beds Inline dripline Every day or two in hot weather
4 Patio containers and baskets Drippers on micro tube Daily in summer, sometimes twice in heat
5 Shrub borders Drippers or leaky hose Once or twice a week, less once established

The schedules are only starting points. Adjust them to weather and soil. Our guide to planning a garden irrigation system explains how much water gardens typically need.

Common zoning mistakes

  • Putting the whole garden on one zone to save money on valves.
  • Mixing drip and sprinklers, or sprays and rotors, on the same valve.
  • Putting sunny and shady beds together, so one is always too wet or too dry.
  • Not allowing for growth: add spare capacity or a spare valve for future beds.
  • Ignoring tubing limits: a long single run can underperform even when the tap has flow to spare.

For the parts you’ll need for multi-zone setups, see irrigation system components. For lawns, read sprinkler head spacing for head-to-head coverage.

The complete guide to planning and system types

Planning a Garden Irrigation System: How to Choose the Right Setup
Read the guide

Keep exploring

Guides from other topics

All topics →