The short answer
Drip irrigation works well on slopes, often better than sprinklers, because it applies water slowly enough to soak in. Slopes do create three specific problems:
- Pressure changes with elevation, so emitters at the bottom put out more than those at the top.
- Lines drain downhill after shut-off, soaking the lowest plants.
- Water can run off before it soaks in.
The main fixes are pressure-compensating (PC) emitters, check valves or non-leak emitters, laterals laid along the contour, zones split by elevation, and low-flow, cycle-and-soak watering.
How elevation changes drip pressure
Water gains about 0.433 psi for every foot it drops and loses the same for every foot it climbs. Over a home garden, that adds up quickly:
| Elevation change | Approximate pressure change |
|---|---|
| 2 ft | 0.9 psi |
| 5 ft | 2.2 psi |
| 10 ft | 4.3 psi |
| 20 ft | 8.7 psi |
On a drip system regulated to around 25 psi, a 10-foot drop changes pressure by roughly 17%. With standard non-compensating emitters, plants at the bottom get noticeably more water than plants at the top. A line running uphill can also lose so much pressure that emitters near the top barely work. For background on target pressures, see drip irrigation operating pressure.
Use pressure-compensating emitters
PC emitters and PC dripline hold their output close to the rated flow across a range of pressures. That makes them the standard choice for slopes. Two points to keep in mind:
- They have a minimum operating pressure, often around 10–15 psi depending on the product. Make sure the highest emitters still receive at least that.
- They also have a maximum. If the bottom of a large slope gains a lot of pressure, check it stays within the emitters’ rating, or add a regulator for the lower section.
Stop low-point drain-down
When a zone shuts off, water left in the tubing flows downhill and drains out of the lowest emitters. On a long slope, this can soak plants at the bottom after every cycle, waste water and cause erosion or crown rot.
Options include:
- Check-valve or non-leak PC emitters and dripline. Many manufacturers offer drip products with a built-in check valve that stays closed below a small pressure, holding water in the line after shut-off.
- Inline check valves on laterals, so each section of slope holds its own water rather than draining into the next.
- Splitting the slope into shorter laterals at different elevations, so each holds less water.
Lay laterals along the contour
The simplest way to even out pressure is to keep each lateral at roughly the same elevation. Run laterals across the slope, along the contour, and feed them from a supply line that runs up or down the slope. Each lateral then has little elevation change along its length, and the supply line handles the height difference.
On terraced gardens, this usually means one lateral per terrace.
When laterals must run up or down the slope
Sometimes rows run downhill, as with vegetable rows on a gentle slope. In that case:
- Downhill runs on gentle slopes can actually help. The pressure gained by dropping elevation can partly offset friction loss along the line, so a lateral fed from the top may deliver more evenly than the same lateral on flat ground. On steeper slopes, the gain overwhelms friction and the bottom ends up over-pressurized, so use PC emitters.
- Avoid long uphill runs. Friction and elevation loss add together, starving the top. If you must run uphill, keep the lateral short and use PC emitters.
- Feed from the top where practical, rather than pushing water uphill from the bottom.
See maximum run length for 1/2-inch drip tubing for how flow and length interact.
Zone by elevation
On larger or steeper slopes, divide the planting into zones by height, such as an upper, middle and lower zone. Each zone gets its own valve, and where needed its own pressure regulator. Benefits:
- Pressure within each zone stays within a narrower range.
- You can run lower zones for less time if water tends to collect there.
- Problems are easier to isolate.
Zoning also lets you group plants by water need, which matters on slopes. The top of a slope often dries faster than the bottom. See how to size a drip irrigation system for planning zone flows.
Place emitters on the uphill side of plants
On sloping ground, water from an emitter moves downhill through the soil. Place emitters on the uphill side of each plant, so the water soaks down through the root zone instead of draining away from it. For trees and larger shrubs on slopes, a curved length of dripline along the uphill side of the root zone can work well. A small soil berm or basin on the downhill side can help hold water in place. See how many drip emitters per tree or shrub.
Prevent runoff and erosion
- Use lower-flow emitters (such as 0.5–1 GPH) so water soaks in rather than running off, especially in clay.
- Cycle and soak. Instead of one long run, schedule several short runs with breaks between them. Many controllers support this directly.
- Mulch. A layer of mulch slows surface flow, protects the soil and covers tubing.
- Terraces, basins or swales on steeper ground hold water near plants.
- Watch for erosion at the bottom. Gullies or exposed soil there suggest drain-down or runoff.
Anchor the tubing
Tubing on slopes tends to slide downhill over time, especially as it expands and contracts with temperature. Secure supply lines and laterals with stakes at regular intervals, often every few feet, and more often on steep ground. Leave a little slack at fittings so tubing can move with temperature without pulling apart.
Test the top and bottom of the slope
After installation, compare emitter output at the top, middle and bottom of each zone:
- Run the zone until lines are full and pressure has settled.
- Catch water from several emitters at each elevation for one minute.
- Compare the readings. A big difference between top and bottom points to pressure problems or mismatched emitters.
See how to calculate drip rate for converting cup readings to GPH. To turn them into a uniformity score, see drip uniformity coefficient. Also watch the lowest emitters for a while after shut-off. Continued dripping means water is draining down the line.
If your slope is fed from a tank rather than a faucet, pressure is much lower and elevation matters even more. See gravity-fed drip irrigation.