Drip System Design

Gravity-Fed Drip Irrigation: Design and Drilling Emitter Holes

Design a gravity-fed drip system from a tank or rain barrel: how much pressure height gives, layout tips, and how to size, space and drill emitter holes.

On this page
  1. How gravity-fed drip works
  2. How much pressure does gravity give you?
  3. Emitters vs. drilled holes at low pressure
  4. Designing the layout
  5. Drilling emitter holes
  6. Testing and adjusting
  7. Common problems

How gravity-fed drip works

A gravity-fed drip system uses the height of a water tank or barrel above the garden, instead of a pump or mains supply, to push water through the lines. It’s popular for rain-barrel gardens, off-grid plots and places without convenient mains water.

The trade-off is pressure. Gravity gives you very little of it, so a gravity system needs a different design from a faucet-fed one: larger, shorter, level lines and outlets that work at low pressure.

How much pressure does gravity give you?

Water pressure from height (“head”) is about 0.433 psi per foot, or roughly 1 psi for every 2.31 feet. In metric, it’s about 0.1 bar (10 kPa) per metre.

Height of water surface above outlets Approximate pressure
1 ft (0.3 m) 0.4 psi
3 ft (0.9 m) 1.3 psi
5 ft (1.5 m) 2.2 psi
10 ft (3 m) 4.3 psi
23 ft (7 m) about 10 psi

The height that counts is from the water surface in the tank down to the emitters, not from the tank’s base. As the tank drains, head falls and so does flow. A tall, narrow tank loses more head per gallon used than a short, wide one.

For comparison, most standard drip components are designed for about 15–30 psi (see drip irrigation operating pressure). A barrel on a 2-foot stand delivers only a few psi at best.

Emitters vs. drilled holes at low pressure

  • Standard non-PC emitters will drip at low pressure, but well below their rated flow and often unevenly.
  • Pressure-compensating (PC) emitters usually need a minimum pressure, often somewhere around 7–15 psi depending on the product, before they open and regulate. Many simply won’t work properly on a low gravity head.
  • Low-pressure or “gravity” drip products, such as some drip tapes, bucket and drum kits, and emitters rated for low head, are designed for this. They’re worth considering if you want predictable flow.
  • Drilled holes in solid tubing or pipe are the cheapest option and work at very low head. They’re more sensitive to clogging and hole-size variation, so they need careful drilling and testing.

Designing the layout

Tank placement and outlet

  • Raise the tank as high as is practical and safe. Every extra foot adds about 0.43 psi. A full tank is very heavy (water weighs about 8.3 lb per gallon), so build the stand to carry the full weight on firm ground.
  • Put the outlet a little above the tank bottom, or use a short standpipe inside, so settled sediment stays in the tank.
  • Use an opaque tank, or shade it, to limit algae growth. Cover openings to keep out debris and mosquitoes.
  • Fit a shut-off valve at the outlet.

Supply pipe and laterals

Because you have so little pressure to spare, friction losses matter more than in a faucet system. Use generously sized supply pipe from the tank, such as 3/4-inch or 1-inch, even if the laterals are 1/2-inch. Avoid unnecessary fittings and sharp bends.

Keep it level and short

At low head, small elevation differences change flow a lot. A 6-inch difference between emitters is about 0.2 psi. That’s minor on a 25 psi system but significant on a 2 psi one.

  • Run laterals along level ground or the contour.
  • Keep laterals short, often well under the lengths you’d use with mains pressure.
  • Feed laterals from the middle, or connect both ends to the supply in a loop, to even out flow.
  • On sloping ground, see designing drip irrigation for slopes.

Filtering without losing too much head

Rainwater and tank water carry debris, so filtering is essential, especially with small drilled holes. But every filter costs some head, and a dirty one costs much more. Choose a filter with a large screen or disc area for its flow, and clean it often. A coarse pre-screen at the tank inlet, such as a gutter screen or first-flush diverter, reduces the load. Our guide to choosing a drip irrigation filter compares screen and disc filters.

Drilling emitter holes

Hole size and estimated flow

Flow through a small hole rises with the hole’s area and with the square root of head. Doubling the head raises flow by only about 40%, while a slightly bigger hole raises it much more. That’s why hole size needs to be consistent.

Using a standard orifice-flow estimate, approximate flows per hole are:

Hole diameter At about 0.5 m (1.6 ft) head At about 1 m (3.3 ft) head
1 mm (about 0.04 in) roughly 5 L/h (1.4 GPH) roughly 7–8 L/h (2 GPH)
1/16 in (about 1.6 mm) roughly 13 L/h (3.5 GPH) roughly 19 L/h (5 GPH)

These figures are rough theoretical estimates. Real flow depends on hole shape, burrs, pipe wall thickness and friction in the line, so treat them as a starting point and measure your own. Two takeaways matter most:

  • Even small holes release more water than a typical 0.5–1 GPH emitter at the same head. Holes around 1 mm, or the smallest bit you can drill cleanly, are a common starting point.
  • Many holes of 1/16 inch or larger can drain a barrel quickly. A 50-gallon (about 190-litre) barrel feeding ten 1/16-inch holes at around 1 m head could, by these estimates, empty in an hour or so.

Hole spacing

Space holes by plant and soil, as you would emitters: closer together in sandy soil, where water moves mostly downward, and further apart in clay, where it spreads sideways. For row crops, 12–18 inches (30–45 cm) is a common range. For individual plants, put a hole at each plant, or two for larger ones. Our article on how many drip emitters per tree or shrub covers placement.

Drilling technique

  • Mark hole positions along a straight line before drilling.
  • Use a sharp bit of one size for the whole system, and drill straight through one wall only.
  • Remove burrs and plastic shavings. Flush the pipe thoroughly before capping the ends.
  • Drill a test section first and measure its flow before drilling the full system.
  • If a hole comes out too large, plug it with a goof plug and drill a new one nearby.

Which way should holes face?

There’s no single rule. Gardeners take different approaches:

  • Holes facing up or to the side are less likely to pick up sediment settling along the bottom of the pipe. Water may squirt slightly at first.
  • Holes facing down drip neatly and help lines drain after shut-off, but they can clog more easily with settled debris.

Some gardeners slide a short sleeve of larger tubing over each hole, or cover lines with mulch, to stop jets and keep holes shaded. Whatever orientation you choose, use it consistently so all holes behave alike.

Testing and adjusting

  1. Fill the tank, open the valve and let the lines fill completely.
  2. Put cups under holes near the start, middle and end of each line, and collect for a set time.
  3. Compare the readings. If the far-end holes collect much less, shorten the lines, enlarge the supply pipe or feed from both ends.
  4. Repeat with the tank about half full to see how much flow falls as head drops.
  5. Use the average flow to set run times (see how to size a drip irrigation system).

Our article on drip uniformity coefficient shows how to turn cup readings into a uniformity score.

Common problems

  • Holes clogging: improve filtering, flush lines by opening the end caps regularly, and keep algae out of the tank.
  • Uneven flow: check that lines are level, supply pipe is large enough and holes are a consistent size.
  • Tank empties too fast: use smaller holes, fewer holes per zone, or split the garden into zones watered in turn.
  • Not enough flow at all: raise the tank, shorten runs, or consider a small pump. With a pump, standard drip parts and a pressure regulator become an option.

For a broader overview of system parts and how water moves through them, see how drip irrigation works.

The complete guide to drip system design

How to Size a Drip Irrigation System: Flow, Water Needs and Capacity
Read the guide

Keep exploring

Guides from other topics

All topics →