Home Drip Installation

How to Install Drip Emitters: Punching Holes and Fitting Barbs

Step-by-step guide to installing drip emitters: punching clean holes in poly tubing, fitting barbs, using 1/4-inch tubing, placing emitters and fixing leaks.

On this page
  1. What You Need
  2. Two Ways to Install Emitters
  3. Where to Put Emitters
  4. How to Punch a Hole in Drip Tubing
  5. Fitting the Emitter or Barbed Connector
  6. Installing Emitters on 1/4-Inch Tubing
  7. Flushing and Testing
  8. Fixing Mistakes and Leaks
  9. Moving and Replacing Emitters

What You Need

  • Drip tubing already laid out and pinned in place, typically 1/2-inch poly tubing
  • Emitters with barbed inlets, and/or 1/4-inch barbed connectors and 1/4-inch micro-tubing
  • A drip hole punch sized for 1/4-inch barbs (most home emitters use this size)
  • Goof plugs for sealing mistakes
  • Stakes to hold 1/4-inch tubing and emitters in place
  • Pruners or a tubing cutter for cutting 1/4-inch tubing

A purpose-made punch is worth buying. A nail, awl or drill bit tends to make ragged or oversized holes that leak. Emitters with a different inlet size need the punch size the manufacturer specifies.

Two Ways to Install Emitters

  1. Directly into the mainline: the emitter’s barb goes straight into a hole in the 1/2-inch tubing. This is quick and tidy, and it works when the tubing runs right beside the plants.
  2. On a 1/4-inch branch: a barbed connector goes into the mainline, a short length of 1/4-inch tubing runs to the plant, and the emitter sits at the end (or the tubing has inline emitters). This lets one mainline serve plants a little way off it, such as shrubs, pots and hanging baskets.

Keep 1/4-inch branches short, since small tubing loses pressure quickly. University of Arizona extension guidance suggests no more than about 5 feet.

Where to Put Emitters

  • New plants: place the emitter near the root ball, a few inches from the stem, so water reaches roots that haven’t spread yet.
  • Established plants: place emitters around the root zone, often toward the edge of the canopy (the “drip line” of the plant), and add more emitters as plants grow.
  • Larger plants: two or more emitters spread around the plant water more of the root zone than one large emitter.
  • Slopes: put emitters on the uphill side of plants so water soaks down through the root zone.

Lay out the emitters on the ground beside the tubing before punching any holes. It is much easier to change your mind at this stage.

How to Punch a Hole in Drip Tubing

  1. Warm stiff tubing. Cold poly tubing is hard to punch and grips barbs poorly. Leaving it in the sun for a while softens it.
  2. Support the tubing. Hold it firmly in one hand, or lay it on a firm surface, so it doesn’t fold or flatten as you push.
  3. Punch straight in, at a right angle to the tubing surface, through one wall only. Don’t push the punch through the far side.
  4. Twist slightly and pull out. Many punches cut a small plug of plastic; make sure it comes out with the punch or falls clear, so it doesn’t end up inside the tubing.
  5. Keep holes on the top or side of the tubing. Holes on the underside are harder to inspect and can draw in soil.

Fitting the Emitter or Barbed Connector

  1. Line up the barb with the hole.
  2. Push it in firmly with a slight twisting motion until the barb pops through and the shoulder sits snugly against the tubing. You’ll usually feel it click past the wall.
  3. Tug it gently. A properly seated barb should not pull out easily.
  4. Check flow direction. Some emitters, especially those with a barb on both ends, are designed to be installed one way round. Follow the markings or instructions.

If the barb feels loose in the hole, the hole is probably too big or torn. Plug it with a goof plug and punch a fresh hole an inch or two away.

Installing Emitters on 1/4-Inch Tubing

  1. Punch a hole in the mainline and insert a 1/4-inch barbed connector.
  2. Cut a length of 1/4-inch tubing to reach the plant, with a little slack.
  3. Push the tubing firmly onto the connector’s barb. Dipping the tubing end in warm water can make this easier.
  4. Push the emitter onto the far end of the tubing (or into it, depending on the design).
  5. Stake the emitter or tubing end beside the plant so it doesn’t wander.

Some emitters can feed several plants through a multi-outlet manifold, and 1/4-inch tubing with built-in emitters can be looped around a large plant or pot.

Flushing and Testing

Ideally, flush the mainline before adding emitters: open the end and run water until it comes out clean, so grit from installation doesn’t lodge in new emitters. Then cap the end, turn the system on, and walk the line:

Fixing Mistakes and Leaks

Problem Likely cause Fix
Water seeping around a barb Torn or oversized hole; tubing too cold when punched Remove the emitter, fit a goof plug, punch a new hole nearby
Emitter popped out Pressure too high; barb not fully seated Check the pressure regulator; reseat or relocate the emitter
Hole in the wrong place Changed layout Seal it with a goof plug
Emitter not dripping Clogged by grit or the plug of plastic from punching Flush the line; clean or replace the emitter
Barbs won’t stay in Fittings don’t match the tubing Check that the tubing and emitters are compatible

Moving and Replacing Emitters

To move an emitter, pull it straight out (pliers help, but avoid crushing it), seal the old hole with a goof plug, and punch a new one where you need it. To replace a clogged emitter, remove it and push in a new one; a hole that has become loose after several changes is better plugged and replaced with a new hole.

For how emitters fit into a complete layout, see the home drip irrigation guide and the components of a drip irrigation system. Specific layouts are covered in drip for tomatoes and drip for hanging baskets.

The complete guide to home drip installation

Home Drip Irrigation: Planning and Installing a Garden Drip System
Read the guide

Keep exploring

Guides from other topics

All topics →