Why Drip Suits Tomatoes
Tomatoes respond well to steady soil moisture. Uneven watering, with dry spells followed by heavy soakings, is linked to fruit cracking and is one factor in blossom end rot. Wet leaves can also encourage some foliar diseases. Drip addresses both: it keeps the root zone evenly moist on a schedule, and it waters the soil without wetting the foliage.
How Far Apart to Plant Tomatoes
Spacing depends on how the plants are grown. Typical ranges used by many gardeners and extension services are:
| Growing method | Spacing between plants | Spacing between rows |
|---|---|---|
| Staked or trellised (often pruned) | About 18–24 in | About 3–4 ft |
| Caged | About 24–36 in | About 4–5 ft |
| Unsupported, sprawling | About 36–48 in | About 4–5 ft or more |
| Compact or determinate varieties | Often toward the closer end of these ranges | Check the seed packet or plant label |
Seed packets and plant labels often give a variety-specific figure, and that is the best guide. Closer spacing means more plants per row but less airflow, so leave enough room to reach in for pruning and harvesting.
Emitter Layout Options
Inline Dripline Along the Row
Inline emitter tubing with emitters every 12 inches, laid along the row a few inches from the stems, is the simplest approach. It works with any plant spacing, since every plant sits near at least one or two emitters, and it waters a continuous strip that roots can spread into. Use 0.5 to 1 gallon per hour emitters, depending on your soil and how long you want to run the system.
For a double row of tomatoes in one bed, run one line along each row, or a single line down the middle if the rows are close together and your soil spreads water well sideways.
Point-Source Emitters at Each Plant
With widely spaced plants, point-source emitters put water only where it is needed. A common layout:
- At planting: one emitter, about 1 to 2 gallons per hour, placed a few inches from the stem.
- As the plant grows: add a second emitter on the opposite side, or move emitters outward, so water covers more of the expanding root zone.
Emitters can go straight into a 1/2-inch line running along the row, or on short 1/4-inch branches. See how to install drip emitters.
Drip Tape
For long rows, drip tape with 8 to 12 inch emitter spacing is cheap and effective. Lay it alongside the row with the emitters facing up, and cover it with mulch. Our guide to drip tape for vegetable rows covers fittings, pressure and run length.
Example Layouts
| Setup | Suggested layout |
|---|---|
| Raised bed, 4 ft wide, two rows of staked tomatoes | Two lines of inline tubing, 12 in emitter spacing, one along each row |
| In-ground row of caged tomatoes 30 in apart | One line of inline tubing along the row, or two point emitters per plant |
| Long rows in a large garden | Drip tape at 8–12 in spacing, one tape per row |
| Sandy soil | Closer emitter spacing (6–8 in) or two lines per row |
| Heavy clay soil | 12 in spacing; lower-flow emitters with longer, less frequent runs |
Tomatoes in Containers and Grow Bags
Containers dry out much faster than garden soil, especially in summer. Give each pot or grow bag one or two emitters, or a small loop of 1/4-inch emitter tubing coiled on the surface, so water spreads across the container rather than running straight down one side. Larger containers generally need two emitters. In hot weather, containers may need watering daily or even more often. The approach is similar to watering hanging baskets; see drip for hanging baskets.
How Much and How Often to Water
Water needs change a lot over the season. Young transplants need little; large plants carrying fruit in hot weather need much more. Many vegetable gardens do well with roughly 1 to 1.5 inches of water per week in moderate weather, and more in hot, dry spells.
To set run time, add up the emitter flow for the plants on a line. For example, 10 plants with two 1-gallon-per-hour emitters each use 20 gallons per hour. One hour delivers about 2 gallons per plant. Start there, then check the soil a few inches down near the plants: it should be moist but not soggy. Deep, less frequent watering generally encourages deeper roots than short daily runs, except in containers and very sandy soil.
Water in the morning where possible, and try to keep the schedule consistent. Sudden large waterings after a dry spell are a common cause of split fruit.
Mulch, Feeding and Other Tips
- Mulch over the drip lines with straw, shredded leaves or similar to keep soil moisture even and reduce evaporation. See whether drip line goes under or over mulch.
- Feeding through drip (fertigation) is possible with a fertilizer injector. Use one with suitable backflow protection, and follow the fertilizer label.
- Stakes and cages: install supports before laying the drip lines, so you don’t puncture tubing later.
- Watch the far end: on long rows, check that the last plants get as much water as the first.
Downsides of Drip for Tomatoes
Drip is not trouble-free. Emitters can clog, especially with hard water or poor filtration. You can’t see how much water reaches the roots, so it is easy to under- or overwater without checking the soil. Tubing can be damaged by tools and animals. And a timer set in spring may not deliver enough water by midsummer. Regular checks and a few minutes of digging to look at soil moisture solve most of these problems.
For layouts in raised beds, see drip irrigation for raised vegetable beds, and for the overall planning steps, the home drip irrigation guide.