Why Drip Works Well in Flower Beds
Overhead sprinklers wet flowers and foliage, splash soil onto leaves, overspray onto paths and walls, and lose water to evaporation. Drip puts water at the base of plants instead. Leaves stay drier, which can help limit some fungal diseases; blooms aren’t battered; weeds between plants get less water; and tubing can be hidden under mulch so the bed looks untouched.
Flower beds are also forgiving places to learn drip: they are usually close to the house and a tap, and mistakes are easy to see and fix.
Pick a Layout That Matches the Planting
Dense Annual Beds and Groundcover
When plants are packed closely, you want the whole bed evenly moist. Use inline emitter tubing laid in parallel rows across the bed, commonly about 12 to 18 inches apart with emitters every 12 inches, closer in sandy soil. The wet strips should meet or nearly meet below the surface. Run the rows from a header of 1/2-inch tubing along one edge, or snake a single line back and forth.
Micro-sprays are an alternative for very dense groundcover or bedding, where you need the surface wet. They use more water per outlet and lose some to wind and evaporation, but they cover gaps that drippers miss.
Perennials and Shrubs with Space Between
Where plants have bare soil or mulch between them, water only the plants. Run 1/2-inch tubing through the bed and add point-source emitters at each plant, either directly in the tubing or on short 1/4-inch branches. As a rough guide, small perennials may need one low-flow emitter, while larger perennials and shrubs need two or more emitters spread around the root zone. Move emitters outward as plants grow. Our guide to installing drip emitters covers the technique.
Mixed Borders
Most real borders combine shrubs, perennials, annuals and bulbs, often with different water needs. Where possible, put thirsty plants and drought-tolerant plants on separate lines or zones so you can water them differently. If they must share a line, give thirsty plants more or higher-flow emitters and drought-tolerant plants fewer or lower-flow ones. A simple two-outlet timer can run a “thirsty” line and a “dry” line on different schedules.
Narrow Borders Along Walls and Fences
Beds along walls, fences and foundations are often in a rain shadow and dry out fast. A single line of inline tubing running along the middle of the border is usually enough for narrow beds; wider beds need two. Keep drip lines a little away from house foundations, and check that water isn’t pooling against walls.
Parts List
- Head assembly at the tap: backflow preventer, timer, filter and pressure regulator
- 1/2-inch poly tubing and matching fittings (tees, elbows, end caps)
- Inline emitter tubing for dense areas, and/or point-source emitters for spaced plants
- 1/4-inch tubing and barbed connectors for branches
- Landscape staples, a hole punch and goof plugs
- Optional: micro-sprays for groundcover, a shut-off valve for each section
For details on each part, see the components of a drip irrigation system.
Installing Drip in a Flower Bed
- Sketch the bed with the tap location and plant groups.
- Fit the head assembly to the tap.
- Run 1/2-inch tubing from the tap to the bed. Where it crosses a lawn or path, bury it shallowly or run it under edging.
- Lay the lines through the bed. Warm the tubing in the sun first so it bends around curves without kinking, and pin it down every few feet. For curving beds, inline tubing can follow the shape of the bed.
- Add emitters or branch lines at each plant, or connect inline tubing rows to a header.
- Flush the system with the ends open, then cap them.
- Test and check every emitter, fixing any leaks.
- Mulch over the lines, typically 2 to 3 inches, keeping mulch back from stems. See whether drip line goes under or over mulch.
Installing drip before planting a new bed is easiest, but adding it to an established bed works well too; slide tubing between plants and pin it down.
Watering Schedule for Flower Beds
Run times depend on emitter flow, soil, weather and plants, so start with a reasonable schedule and adjust:
- Newly planted beds need more frequent watering while roots establish, often several times a week in warm weather.
- Established perennials and shrubs generally do better with deeper, less frequent watering than with short daily runs.
- Annuals and containers within beds usually need more frequent watering than established perennials.
Check soil moisture a few inches down near emitters and between them a few hours after watering. If the root zone is dry, water longer; if it stays soggy, cut back. Water in the early morning where possible.
Seasonal Care and Adjustments
- Spring: flush the lines, clean the filter, check for winter damage, and re-pin tubing disturbed by digging.
- Summer: increase run times in heat, and add emitters for plants that look stressed.
- Autumn: reduce watering as temperatures drop; add emitters for newly planted shrubs and bulbs.
- Winter: in frost-prone areas, drain the lines and bring the timer, filter and regulator indoors.
When you divide or move perennials, move their emitters too, and plug the old holes.
Common Problems
- Dry patches in dense beds: rows of inline tubing too far apart. Add a row or switch to closer emitter spacing.
- Clogged emitters with hard water: clean the filter, flush regularly, and consider pressure-compensating, self-flushing emitters.
- Some plants soggy, others dry: plants with different needs on the same line. Rezone or change emitter flows.
- Lines cut during weeding or planting: mark lines with flags and keep a simple map.
For a complete planning overview, see the home drip irrigation guide. Hanging baskets and pots near beds can be added with the methods in drip irrigation for hanging baskets.