Home Drip Installation

How to Convert a Sprinkler Zone to Drip Irrigation

Convert a sprinkler zone to drip step by step: retrofit kit vs control zone kit, capping heads, sizing zone flow, choosing dripline or emitters and setting run times.

On this page
  1. The Key Rule: Convert the Whole Zone
  2. Is This Zone a Good Candidate?
  3. Two Ways to Convert
  4. Step-by-Step Conversion
  5. Sizing the Zone: Add Up the Flow
  6. Choosing Dripline or Emitters
  7. Reprogramming the Controller
  8. Why Conversions Fail

The Key Rule: Convert the Whole Zone

A sprinkler zone is every head controlled by one valve. When you convert to drip, every outlet on that zone must become drip. Sprayers apply water in gallons per minute; drip applies it in gallons per hour. If they share a valve, either the drip area is flooded while the spray area gets enough, or the spray area goes thirsty while the drip area gets enough. Drip also needs filtered water at much lower pressure than spray heads.

So the job is: deal with every spray head on the zone, add filtration and pressure regulation, then lay drip.

Is This Zone a Good Candidate?

Good candidates are zones that water planting beds, shrubs, borders, vegetable areas or trees, especially where spray hits walls, windows, fences or paths. Converting these zones usually saves water and reduces disease and weeds.

Poor candidates are zones that are mostly lawn. Drip is not a practical way to water turf for most homeowners. If a zone mixes lawn and beds, you have three choices: leave it as spray, move the bed heads onto a new valve, or convert the beds and re-plumb the lawn heads onto another zone.

Some water utilities offer rebates for converting spray to drip. Check before you buy parts.

Two Ways to Convert

Option 1: Retrofit Kit on One Spray Head

A retrofit (or spray-to-drip) kit screws onto an existing spray body or riser. It contains a filter and pressure regulator, and provides an outlet for drip tubing. You fit it to one head, usually the one most convenient for reaching the beds, and cap all the other heads on the zone.

This is the easiest conversion: no digging at the valve, no new wiring. It suits smaller zones. Kits have a flow range; your drip zone needs to fall within it.

Option 2: Drip Control Zone Kit at the Valve

A control zone kit combines a valve, filter and pressure regulator in one assembly, installed at the valve manifold in place of (or in addition to) the existing valve. All the heads on the zone are capped, and new drip supply tubing runs from the kit to the beds.

This is the more robust option for larger zones, because the filter and regulator are at the source and easy to service. It involves more plumbing and possibly digging. Kits come with different pressure settings (commonly 25, 30 or 40 psi) and flow ranges, so choose one that matches your dripline and zone size.

Step-by-Step Conversion

  1. Find every head on the zone. Run the zone and push a flag beside each spray head. It is easy to miss one hidden in a shrub.
  2. Decide your method: retrofit at one head, or control zone kit at the valve.
  3. Cap the unused heads. Remove the nozzle and riser, or the whole spray body, and fit a cap on the riser or fitting below it. An open head on a drip zone dumps water and drops pressure for the whole zone.
  4. Install the retrofit kit or control zone kit, following the manufacturer’s instructions and flow arrows.
  5. Lay the drip supply line (usually 1/2-inch poly tubing, or the dripline maker’s size) from the kit to the beds. Use fittings designed for that exact tubing size.
  6. Lay dripline or emitter tubing through the beds and pin it in place.
  7. Flush the lines with the ends open until water runs clean.
  8. Close the ends with end caps or flush valves.
  9. Test the zone, walk every line, and check for leaks and dry spots.
  10. Mulch over the lines if you like; see should drip line go under or over mulch.

If you need to dig near utility lines, contact your local utility-locating service first (in the US, call 811).

Sizing the Zone: Add Up the Flow

Total the flow of all the emitters on the zone, then divide by 60 to convert gallons per hour to gallons per minute:

Layout Total flow Zone flow
100 ft of 0.6 gph dripline, emitters every 12 in 100 x 0.6 = 60 gph 1.0 gpm
150 ft of 0.9 gph dripline, emitters every 18 in 100 x 0.9 = 90 gph 1.5 gpm
30 shrubs with two 2 gph emitters each 60 x 2 = 120 gph 2.0 gpm

Then check:

  • The zone flow sits inside the kit’s rated flow range. Below the minimum, the regulator may not hold pressure; above the maximum, the far end may be starved.
  • Each run of dripline is within the manufacturer’s maximum length for your inlet pressure.

Choosing Dripline or Emitters

  • Dense beds and groundcover: inline dripline, commonly with emitters every 12 or 18 inches, laid in parallel rows so the wet strips meet.
  • Spaced shrubs and perennials: 1/2-inch tubing with point-source emitters, two or more per larger plant.
  • Trees: a ring of dripline or several emitters around the root zone, or bubblers. Trees in lawns often need their own zone.
  • Slopes: dripline with check valves helps stop the line draining to the low end after each run.

See the best type of drip irrigation and how to install drip emitters for more on each.

Reprogramming the Controller

Drip run times are much longer than spray run times, often measured in tens of minutes or hours rather than a few minutes. Don’t keep the old spray schedule. Start from the plants’ needs and the zone’s flow, run the zone, and check soil moisture a few inches down near emitters several hours later. Adjust by season. Established shrubs usually do better with deeper, less frequent watering.

Why Conversions Fail

  • Only part of the zone was converted, leaving spray and drip on the same valve.
  • A head was left uncapped, dumping water and dropping pressure.
  • No filter or regulator, so emitters clog or fittings blow off.
  • Mismatched fittings and tubing sizes: different tubing sizes need different fittings.
  • Zone flow outside the kit’s range.
  • Runs too long for the dripline at that pressure.
  • Lines not flushed before capping, so installation debris clogs emitters.
  • Spray-length run times left on the controller.

For planning the drip side in more detail, see the home drip irrigation guide and the components of a drip irrigation system.

The complete guide to home drip installation

Home Drip Irrigation: Planning and Installing a Garden Drip System
Read the guide

Keep exploring

Guides from other topics

All topics →