The Short Answer
There is no single best drip irrigation system; the best type depends on how your plants are arranged. As a general guide:
- Inline emitter tubing (dripline) is the best all-round choice for raised beds and closely planted beds.
- Point-source emitters on 1/2-inch tubing are best for widely spaced plants such as shrubs, tomatoes and containers.
- Drip tape is best and cheapest for long, straight vegetable rows.
- Micro-sprays suit dense groundcover where you need a wider wet area.
If you are unsure, inline emitter tubing with pressure-compensating emitters is the most forgiving option for a typical home vegetable garden.
The Main Types of Drip Irrigation
Inline Emitter Tubing (Dripline)
Tubing with emitters built in at fixed intervals, such as every 6, 12 or 18 inches. It creates a continuous wet strip, so you can plant anywhere along it. It is quick to install, durable and available with pressure-compensating emitters for long runs and slopes. The downside is that fixed spacing doesn’t suit plants that are far apart.
Point-Source Emitters on Poly Tubing
Individual emitters punched into 1/2-inch tubing, or connected to it with short lengths of 1/4-inch tubing, placed exactly where each plant needs water. This is the most flexible option: you can give a large shrub 4 gph and a small perennial 0.5 gph on the same line. It takes longer to install and has more parts that can clog or get knocked out. See how to install drip emitters.
Drip Tape
Thin-walled, flat tubing with built-in emitters, used for row crops. It is very cheap per foot and runs at low pressure, around 8 to 15 psi. Thin tape is often treated as single-season; thicker tape can last several seasons with care. It is easy to puncture and does not suit curves or permanent landscape beds. See drip tape for vegetable rows.
1/4-Inch Soaker Dripline and Soaker Hose
Small-diameter tubing with closely spaced emitters, or porous soaker hose that weeps along its length. Both are easy to lay in small beds, around pots or in curves. Soaker hose is cheap but its output is uneven on long or sloped runs; 1/4-inch emitter line is more consistent but still limited in run length.
Micro-Sprays and Bubblers
Micro-sprays and microjets spray a small circle or part-circle and suit dense groundcover, closely planted annuals and seedbeds. Bubblers release a higher flow for trees and large shrubs. Both use more water per outlet than drippers, and sprays lose more to evaporation and wind. See micro irrigation kit installation.
Best Type by Garden Situation
| Garden situation | Best starting choice | Why |
|---|---|---|
| Raised vegetable beds | Inline emitter tubing at 6–12 in spacing | Even moisture across the bed; easy to replant |
| Long, straight vegetable rows | Drip tape | Cheap, low pressure, covers long rows |
| Tomatoes, squash, peppers spaced apart | Inline tubing at plant spacing, or point emitters | Water where the plants are, not between them |
| Shrubs and trees | Point emitters or loops of inline tubing; bubblers for large plants | Different plants need different flows |
| Containers and hanging baskets | Point emitters on 1/4-inch tubing | One or more emitters per pot |
| Curving flower beds and borders | Inline tubing snaked through the bed, or 1/4-inch dripline | Follows curves; can be hidden under mulch |
| Dense groundcover | Micro-sprays or closely spaced dripline | Wider wetted area |
| Rain barrel or gravity supply | Non-PC emitters or low-pressure dripline | Works at very low pressure |
Pressure-Compensating or Not?
Pressure-compensating (PC) emitters keep roughly the same output across a range of pressures, so the first and last emitters on a run deliver about the same amount. That matters on long runs, on slopes and in systems with many emitters. Many PC emitters are also self-flushing, which reduces clogging. They cost more and need a minimum pressure to work properly.
Non-PC emitters are cheaper and simpler, and their output rises and falls with pressure. They are fine on short, flat runs, and often the better choice for gravity systems, where pressure is too low for PC emitters to work.
For most home gardens on a tap with a pressure regulator, PC emitters or PC dripline are worth the small extra cost.
Other Factors That Affect the Choice
- Water source: a household tap supports almost any type with a regulator. A rain barrel or gravity tank limits you to low-pressure parts; see drip from a rain barrel.
- Slope: PC emitters, and dripline with check valves that stop the line draining to the low end, help on slopes.
- Water quality: hard water and water with sediment clog small emitters. Good filtration and larger-passage emitters help.
- Permanence: perennial beds suit durable dripline; annual rows that get tilled suit drip tape you can roll up or replace.
- Soil: sandy soil needs closer emitter spacing because water spreads less sideways; clay spreads water further but absorbs it slowly.
Kit or Build Your Own?
Kits are a good way to start: they include a compatible head assembly, tubing and fittings, and take the guesswork out of matching sizes. Their limitation is that they are sized for a typical garden, which may not be yours. Building from separate parts costs less per foot for larger gardens and lets you choose exactly the right emitter for each area. Many gardeners start with a kit and expand it with parts from the same brand or tubing size.
For a full walkthrough of planning and installing a system, see the home drip irrigation guide, and for raised beds specifically, drip irrigation for raised vegetable beds.