Planning and System Types

What are the types of micro irrigation?

Micro irrigation types include drip emitters, inline dripline, drip tape, micro-sprinklers, misters, bubblers, porous hose, subsurface drip and ollas. How they compare.

On this page
  1. What counts as micro irrigation
  2. The main types
  3. Comparison table
  4. What all micro systems need
  5. Advantages and drawbacks
  6. Choosing the right type

Micro irrigation, also called localised or low-volume irrigation, delivers small amounts of water close to plants. The main types are point-source drip emitters, inline dripline, drip tape, micro-sprinklers and micro-sprays, misters and foggers, bubblers, porous (soaker) hose and subsurface drip. Traditional ollas, buried clay pots, are an ancient form of the same idea. They all aim to wet the root zone rather than the whole ground surface, which usually saves water compared with overhead sprinklers.

What counts as micro irrigation

Micro systems share a few traits:

  • They operate at low pressure compared with sprinkler systems.
  • Each outlet has a low flow, typically measured in litres (or gallons) per hour rather than per minute.
  • Water goes to a small area near each plant or row.
  • They usually run on small-bore polyethylene tubing with a filter and pressure regulator at the start.

The main types

Point-source drip emitters

Individual drippers are pushed into tubing exactly where each plant sits. Common flow ratings are a few litres per hour. Pressure-compensating versions keep output steady along long runs and on slopes.

  • Best for: shrubs, mixed borders, containers (via micro tube), trees (several emitters each).

Inline dripline

Tubing with emitters built into the wall at fixed spacing, often every 30 cm or so.

  • Best for: vegetable rows, raised beds, hedges, closely planted borders.
  • Plus: fewer separate parts to come loose, and it’s quick to lay.

Drip tape

A thin-walled, flat tape with emitters or slits along it. It’s cheaper than dripline but less durable, and it’s often replaced every season or every few seasons.

  • Best for: annual vegetable rows, especially on larger plots and market gardens.

Micro-sprinklers and micro-sprays

Small heads on stakes or risers that spray a fan or a spinning stream over a small radius.

  • Best for: ground cover, densely planted beds, under fruit trees, seed beds.
  • Note: more evaporation and drift than drip, and they wet foliage.

Misters and foggers

Very fine nozzles that produce mist, mainly to raise humidity or cool the air rather than to water soil.

  • Best for: propagation, greenhouses, cooling patios.
  • Note: they need clean water to avoid blockage.

Bubblers

Low-pressure outlets that release a gentle gush into a basin around a plant.

  • Best for: trees and large shrubs, planters.

Porous (soaker) hose

Hose with a porous wall that seeps water along its whole length. See leaky hose and soaker hose garden irrigation.

  • Best for: straight rows and hedges.
  • Note: output varies with pressure and length.

Subsurface drip

Dripline buried in the root zone, so the surface stays dry.

  • Best for: lawns (specialist systems), permanent beds, hot dry climates.
  • Note: hard to inspect, and it can be damaged by digging or root intrusion. Use products designed for burial.

Ollas and clay pot irrigation

Unglazed clay pots buried next to plants and filled by hand. Water seeps out through the clay as the soil dries.

  • Best for: a few high-value plants, allotments without mains water, low-tech setups.

Comparison table

Type Typical outlet flow Wetting pattern Visibility Best fit
Drip emitter Low (a few L/h) Small spot at each plant Visible Shrubs, pots, borders
Inline dripline Low (per emitter) Continuous strip Visible or under mulch Rows, beds
Drip tape Low Continuous strip Visible or shallowly buried Annual rows
Micro-sprinkler Moderate Small circle or fan Visible Ground cover, under trees
Mister/fogger Very low Airborne mist Visible Propagation, humidity
Bubbler Moderate to high Flooded basin Visible Trees, planters
Porous hose Variable Continuous strip Visible or under mulch Rows, hedges
Subsurface drip Low Below-ground strip Hidden Permanent plantings
Olla Very slow Small radius underground Mostly hidden Single plants

What all micro systems need

  • A filter. Small outlets block easily. This is the most important part.
  • A pressure regulator on mains supplies, sized for the tubing and emitters.
  • Backflow protection where connected to drinking water. See do you need a backflow preventer for garden irrigation.
  • Flushable ends, so sediment can be cleared.

Irrigation system components explains each part.

Advantages and drawbacks

Advantages:

  • Generally high water efficiency, with little lost to evaporation or runoff
  • Dry foliage, which can reduce some leaf diseases
  • Fewer weeds between plants, because paths stay dry
  • Works with low flow and pressure, and with timers

Drawbacks:

Choosing the right type

  • Pots and mixed planting: point-source emitters.
  • Rows and raised beds: inline dripline or drip tape.
  • Dense ground cover: micro-sprinklers.
  • Trees: bubblers or a ring of emitters.
  • No mains water: ollas, or gravity drip from a water butt.

For simpler alternatives to small-bore drip, see 8 types of irrigation systems. If you’re deciding between porous hoses, see is a weeper hose better than a soaker hose.

The complete guide to planning and system types

Planning a Garden Irrigation System: How to Choose the Right Setup
Read the guide

Keep exploring

Guides from other topics

All topics →