The cost of a garden irrigation system ranges from the price of a leaky hose and a tap timer to several thousand for a professionally installed, multi-zone sprinkler system. Surface drip and leaky hose systems you fit yourself are usually the cheapest way to automate watering beds and pots. Buried lawn sprinklers installed by a contractor cost the most, mainly because of labour, trenching, valves and controllers.
Prices vary by country, region and supplier, and they change over time. Use the figures below as rough guides, and get current quotes for your own garden.
What drives the cost
- Area and layout: more ground means more pipe, more outlets and often more zones.
- System type: surface drip costs much less than buried sprinklers.
- Number of zones: each zone needs a valve and wiring, or a timer outlet. Low water pressure or flow means more zones are needed. See how to divide your garden into irrigation zones.
- Water source: a mains tap is simplest. Wells need pumps, and rainwater may need tanks and pumps.
- Soil and access: rocky ground, tree roots, paving to bore under, and narrow side access all raise labour costs.
- Controller: a basic battery timer is cheap, while a smart Wi-Fi controller with sensors costs more.
- Backflow and compliance: some areas require a specific, sometimes professionally tested, backflow device for permanent systems. See do you need a backflow preventer for garden irrigation.
Typical cost ranges by system type
| System | Relative cost (DIY) | Notes |
|---|---|---|
| Leaky/soaker hose and tap timer | Lowest | Good for a few beds or rows |
| Drip starter kit for pots or a greenhouse | Low | Kits cover a set number of plants |
| Parts-based drip for a whole garden | Low to moderate | Depends on tubing length and the number of zones |
| Hose-end sprinklers on a timer | Low | Cheap, but less even coverage |
| Buried pop-up sprinkler system | High | Most of the professional cost is labour |
| Rainwater tank, pump and drip | Moderate to high | The tank is usually the biggest cost |
| Well pump and filtration | Moderate to high | Depends on depth and water quality |
For US lawn sprinkler systems, one published consumer cost guide puts the average professionally installed system at roughly $2,500, with a typical range of about $0.20–$1 per square foot. It quotes drip systems at a few hundred dollars and per-zone costs in the hundreds to low thousands. Treat these as a snapshot from one source, not a quote.
DIY vs professional installation
| DIY | Professional | |
|---|---|---|
| Up-front cost | Parts only | Parts plus labour, usually the larger share |
| Best suited to | Surface drip, leaky hose, small sprinkler layouts | Buried multi-zone sprinklers, large or complex sites |
| Design quality | Depends on your planning | Usually includes a coverage design |
| Time | An afternoon to a few weekends | Often a day or two for a typical lawn |
| Warranty | Parts only | Often covers workmanship too |
| Compliance | You’re responsible for backflow and local rules | Installer usually handles it |
Most surface systems are well within DIY range. See DIY garden irrigation. Buried sprinklers are possible to DIY but take more work. How to install pop-up sprinklers in an existing lawn shows what’s involved.
Running and maintenance costs
- Water. A well-run drip system often uses less water than hand-watering. A badly set timer can use more. If you pay for metered water, this is the biggest ongoing cost.
- Batteries and power for timers, controllers and pumps.
- Replacement parts: drippers, filters and washers. Soaker hose and drip tape wear out sooner than good dripline.
- Seasonal work: spring start-up and autumn drain-down. In cold climates, professional winterising (blowing out buried lines) is often a yearly charge.
- Repairs: heads damaged by mowers, and tubing nicked by tools or animals.
Hidden and extra costs
- New outdoor tap or a dedicated supply pipe
- Backflow device, and any required testing
- Pressure regulator and filter, if not included in a kit
- Rain or soil moisture sensors
- Making good: re-turfing trenches, replacing paving
- Permits, in some areas
How to keep costs down
- Start small: automate containers and vegetable beds first, where the time savings are largest.
- Use surface drip under mulch instead of buried pipe where it looks acceptable.
- Buy one brand and tube size to avoid wasted adaptors.
- Measure your flow and plan zones before buying, so you don’t buy parts twice.
- Do the digging yourself and pay a professional only for design or the final connection.
- Use rainwater where you can, to cut water bills over time. See building a PVC rainwater harvesting system.
Comparing installer quotes
Ask each installer to itemise:
- The number of zones, and the type and number of heads or emitters per zone
- Pipe sizes and materials
- The controller model, and any sensors
- The backflow device type, and whether testing is included
- Who makes good the lawn and paving
- Warranty on parts and labour
- Annual service or winterising costs
A cheaper quote with fewer zones or lower-grade parts may cost more in the long run if coverage is poor. For the design questions to settle first, see planning a garden irrigation system.