Planning and System Types

Leaky Hose and Soaker Hose Garden Irrigation

How leaky and soaker hoses work, where they suit, how to lay them out, pressure and run-length limits, run times, and how they compare with drip irrigation.

On this page
  1. What leaky hose is and how it works
  2. Where leaky hose works well (and where it doesn’t)
  3. Pressure, flow and run length
  4. How to lay out a leaky hose system
  5. How long to run it
  6. Connecting a timer and backflow protection
  7. Leaky hose vs drip irrigation
  8. Lifespan, care and troubleshooting

Leaky hose is probably the easiest way to get water to the roots of a bed. You lay it along the plants, connect it to a tap, and water seeps out along its whole length. The idea is simple. It still pays to understand how it behaves, though, because leaky hose is more sensitive to pressure, length and slope than most people expect.

What leaky hose is and how it works

Leaky hose goes by several names: soaker hose, porous hose, weeper hose, sweat hose. Most is made from recycled rubber, sometimes blended with polyethylene, with a porous wall. Other versions are flat, fabric-covered hoses. In both cases water passes through the wall at low pressure and soaks into the soil, rather than spraying into the air.

The names are mostly used interchangeably. We look at the small differences in is a weeper hose better than a soaker hose.

Where leaky hose works well (and where it doesn’t)

Good for:

  • Straight rows of vegetables, soft fruit or cut flowers
  • Hedges and newly planted hedging
  • Densely planted borders, where individual drippers would be impractical
  • Coiling around a newly planted tree or shrub

Less suited to:

  • Containers and hanging baskets, which suit drip emitters better
  • Lawns, which need overhead coverage
  • Long runs, slopes, or very low-pressure sources such as a water butt on the ground
  • Widely spaced plants, where much of the hose wets bare soil

Pressure, flow and run length

Leaky hose is designed for low pressure. On full mains pressure it can spurt, sweat unevenly or split. Many manufacturers recommend a pressure reducer, and some kits include a flow-restricting washer. Follow the instructions for your product.

Run length matters as much as pressure. Water loses pressure as it travels, so the end of a long hose seeps less than the start. Manufacturers usually give a maximum run length. Where they don’t, a common rule of thumb is to keep single runs well under about 30 m (100 ft). To cover more ground, feed several shorter runs from a supply hose or a manifold rather than one long loop.

Slope causes a similar problem: water collects at the low end. On sloping beds, run the hose across the slope, along the contours, rather than up and down it.

How to lay out a leaky hose system

  1. Lay the hose in the sun for an hour so it’s flexible and doesn’t kink.
  2. Run it close to the plants, within about 10–15 cm of the stems in a row.
  3. Space parallel lines by soil type. Water spreads sideways further in clay than in sand. Sandy soil needs lines closer together, and clay can take wider spacing. Somewhere around 30–45 cm between lines is a common starting point for loam, adjusted after you check the soil.
  4. Use plain supply hose to cross paths and lawns, and switch to leaky hose only where you want water.
  5. Pin it down with U-shaped pegs.
  6. Cover with mulch, not soil. Mulch reduces evaporation and protects the hose from sunlight. Burying it in soil can encourage roots and silt to block the pores.
  7. Fit an end cap, and leave it accessible for flushing.

How long to run it

There’s no fixed time, because output depends on pressure, hose type and length. To calibrate yours:

  1. Run the hose for 30 minutes.
  2. Wait an hour, then dig a small hole beside the hose with a trowel.
  3. See how deep and how wide the moist soil reaches. For most vegetables, you want moisture down into the root zone, often 15–20 cm or more.
  4. Adjust the run time up or down, and check again a few days later.

Once you know how long it takes to wet the root zone, set a timer to match and adjust through the season.

Connecting a timer and backflow protection

A typical tap assembly for leaky hose is: tap, then backflow protection (often built into newer outdoor taps), then a timer, then a pressure reducer, then the hose connector. A filter helps, because grit can block the porous wall. How to connect a garden irrigation system to an outdoor tap explains the order and threads, and do you need a backflow preventer covers the rules.

Leaky hose vs drip irrigation

Leaky/soaker hose Drip (emitters or dripline)
Set-up Very simple Simple to moderate
Up-front cost Low Low to moderate
Evenness of watering Varies with pressure, length and slope More even, especially with pressure-compensating emitters
Containers Not practical Yes, via micro tube
Measuring output Hard to know exactly Emitters have a rated flow
Typical lifespan Often a few seasons Often longer, depending on quality and UV exposure
Best for Rows, hedges, dense beds Most beds, pots, borders

Many gardeners use both: leaky hose for hedges and long rows, and drip for pots and mixed borders. See the types of micro irrigation for the wider family.

Lifespan, care and troubleshooting

How long leaky hose lasts depends on the material, sunlight, water quality and how roughly it’s treated. Many last a few seasons, and good-quality hose kept under mulch and stored over winter often lasts longer.

Care tips:

  • Flush it at the start of each season by removing the end cap.
  • Lift it, drain it and store it indoors over winter in frost-prone areas.
  • Don’t drive or walk on it, and don’t leave it exposed to strong sun for long periods.

Troubleshooting:

Problem Likely cause Fix
Dry far end Run too long, low pressure, or uphill Shorten runs, feed from the middle, run along contours
Spurting jets Pressure too high or a split Fit a pressure reducer, cut out the split and join with a connector
Patchy sweating Blocked pores, or hard water Flush. Consider a filter, or replace old hose
Leaking at the tap Worn washer or mismatched thread Replace the washer, check the BSP/GHT thread match
Puddles in one spot Low point in the bed Re-route, or add a short plain-hose section there

If you’re trying to decide whether leaky hose suits your whole garden, our guide to planning a garden irrigation system puts it alongside the other options.

The complete guide to planning and system types

Planning a Garden Irrigation System: How to Choose the Right Setup
Read the guide

Keep exploring

Guides from other topics

All topics →