The three numbers that size a drip system
Sizing a drip system mostly means comparing three numbers:
- Supply: how much water your faucet, valve or pump can deliver (flow), and at what pressure.
- Demand: how much water your plants need, and how much flow the emitters you pick will draw.
- Capacity: how much flow your tubing can carry before friction starves the far end.
If demand is higher than supply or capacity, you split the garden into zones that run one at a time. Once the zones are set, you work out how long each one runs to meet your plants’ water needs. The steps below go through that in order, and a worked example at the end puts it all together.
Step 1: Measure your water supply
Flow rate with a bucket test
The simplest way to measure flow is to time how long it takes to fill a container of known size:
- Use the faucet or valve that will feed the drip system. Turn off other water use in the house.
- Open the faucet fully and time how long it takes to fill a 5-gallon bucket (or a 10-litre bucket).
- Work out the flow:
- Gallons per minute (GPM) = gallons ÷ seconds × 60
- Gallons per hour (GPH) = GPM × 60
- Litres per hour (L/h) = litres ÷ seconds × 3,600
For example, 5 gallons in 40 seconds is 5 ÷ 40 × 60 = 7.5 GPM, or 450 GPH.
Drip parts are rated in gallons per hour (or litres per hour), so converting to GPH now keeps the rest of the math easy.
Static pressure
Thread an inexpensive pressure gauge onto the faucet and open it with no water flowing elsewhere. That’s your static pressure. Home supplies often read somewhere around 40–80 psi. Most drip components are designed for much less, so nearly every faucet-fed system needs a pressure regulator. Our guide to drip irrigation operating pressure covers target ranges and how to check pressure while the system is running.
Leave a margin
A bucket test is done with the faucet wide open into free air. Once you add a backflow preventer, filter, regulator and tubing, some flow is lost. Household demand (a shower, a washing machine) can also cut into supply while the drip system is running. Many designers plan to use no more than about three-quarters of the measured flow. In the example above, that’s roughly 335 GPH.
Step 2: Estimate how much water your plants need
The ET-based formula
Plant water use is usually estimated from reference evapotranspiration (ETo), the water a standard grass surface loses on a given day. Many weather services and agricultural extension offices publish it. You then adjust ETo for your plants with a crop coefficient (Kc) or plant factor:
Gallons per day = ETo (inches/day) × Kc × area (sq ft) × 0.623 ÷ efficiency
- 0.623 converts one inch of water over one square foot into gallons.
- Kc or plant factor is around 1.0 for actively growing vegetables at full size. It’s lower for young plants and many shrubs, and often much lower for drought-tolerant landscapes.
- Efficiency accounts for losses and uneven delivery. Around 0.85–0.9 is a common assumption for a well-built drip system. Our article on drip irrigation efficiency explains where those losses come from.
- Area is the planted or root-zone area being watered, not your whole yard. For trees and shrubs, it’s often the canopy area.
Metric version
Metric is simpler because 1 mm of water over 1 m² is exactly 1 litre:
Litres per day = ETo (mm/day) × Kc × area (m²) ÷ efficiency
A 10 m² vegetable bed with an ETo of 6 mm/day and a Kc of 1.0 needs about 60 litres a day before losses, or about 67 litres at 90% efficiency.
When you don’t have ET data
If you can’t find local ET figures, you can start from emitter-based rules of thumb (for example, a set number of emitters per shrub or tree) and adjust by watching the soil. Dig down a few inches a day after watering to see how deep the moisture went. Our article on how many drip emitters to use per tree or shrub covers that approach. For more on the general math, see how to calculate irrigation.
Step 3: Choose emitters and add up the flow
Common emitter flow rates:
| Emitter rating | Approximate metric equivalent |
|---|---|
| 0.5 GPH | about 1.9 L/h (often sold as 2 L/h) |
| 1 GPH | about 3.8 L/h (often sold as 4 L/h) |
| 2 GPH | about 7.6 L/h (often sold as 8 L/h) |
Inline dripline, which is tubing with emitters built in at a fixed spacing, is usually rated per emitter (for example, 0.5 or 0.9 GPH at 12-inch spacing). It’s sometimes rated as total flow per 100 feet.
As a general pattern, sandy soils suit higher flows at closer spacing, while clay soils suit lower flows that give water time to soak in. Then add it up:
Zone flow (GPH) = number of emitters × emitter flow (GPH)
For dripline: zone flow = (feet of dripline ÷ emitter spacing in feet) × flow per emitter.
If you need to check what your emitters actually deliver, rather than what the label says, see how to calculate drip rate.
Step 4: Check what your tubing can carry
Even with plenty of supply, the tubing itself limits how much flow a single line can carry. Exact figures depend on the tubing’s inside diameter and the manufacturer. Commonly quoted ballpark limits are:
| Tubing | Typical maximum flow | Typical maximum run |
|---|---|---|
| 1/4-inch microtubing | roughly 25–30 GPH | about 30 ft or less |
| 1/2-inch poly | roughly 200–240 GPH | about 200 ft |
| 3/4-inch poly | roughly 450–500 GPH | longer runs possible; check charts |
Length and flow interact: a long run with high-flow emitters loses pressure much faster than a short run with low-flow emitters. Our article on maximum run length for 1/2-inch drip tubing explains how to stay within limits and work around them.
Step 5: Split the garden into zones
You need more than one zone when:
- Total flow is higher than usable supply. For example, 500 GPH of emitters on a 335 GPH supply.
- Total flow is higher than tubing capacity. For example, 300 GPH on a single 1/2-inch line.
- Plants have very different water needs. Vegetables watered daily shouldn’t share a zone with established shrubs watered weekly.
- Sun, soil or elevation differ a lot. Hillside beds often behave differently from flat ones. See designing drip irrigation for slopes.
A multi-outlet hose timer or a set of valves on a manifold lets each zone run on its own schedule.
Step 6: Work out the run time
Once you know how many gallons a zone needs and how many gallons per hour it delivers:
Run time (hours) = gallons needed ÷ zone flow (GPH)
For beds with evenly spaced emitters, you can also work in inches:
Application rate (inches/hour) = 231 × emitter GPH ÷ (emitter spacing in inches × row spacing in inches)
Run time (hours) = inches needed ÷ application rate
Whether you water daily or every few days depends on soil type, root depth and weather. Sandy soils hold less water and usually need shorter, more frequent cycles.
Worked example: a small home garden
Supply: 5 gallons in 40 seconds = 450 GPH. Planning to about 75% gives roughly 335 GPH usable. Static pressure is 60 psi, so a 25 psi regulator goes on the head assembly.
Zone A: vegetables. Three 4 × 8 ft beds (96 sq ft total), each with three rows of 0.5 GPH dripline at 12-inch spacing (rows about 16 inches apart).
- About 8 emitters per row × 3 rows × 3 beds = 72 emitters × 0.5 GPH = 36 GPH
- Peak summer ETo of 0.25 in/day × Kc 1.0 × 96 sq ft × 0.623 ≈ 15 gallons/day. At 90% efficiency, that’s about 16.6 gallons/day.
- Run time: 16.6 ÷ 36 ≈ 0.46 hours, or about 28 minutes a day at peak.
- Cross-check with the application rate: 231 × 0.5 ÷ (12 × 16) ≈ 0.60 in/hr. The beds need about 0.28 inches including losses, and 0.28 ÷ 0.60 ≈ 0.46 hours. Both methods agree.
Zone B: shrubs and trees. 20 shrubs with two 1 GPH emitters each (40 GPH), plus 5 young trees with six 2 GPH emitters each (60 GPH): 100 GPH total.
Both zones together would only draw 136 GPH, well within the supply and a single 1/2-inch line. They’re still split because vegetables in midsummer need short daily watering, while woody plants do better with longer, less frequent soaks.
How to measure an existing drip system
Tubing size
“1/2-inch” drip tubing isn’t one standard size. Common sizes include roughly 0.600 in inside diameter (ID) × 0.700 in outside diameter (OD), and 0.620 × 0.710. Measure the outside diameter with calipers, or check the print on the tubing, before buying compression fittings. Fittings made for one size may leak or blow off another.
Emitter output
Set a measuring cup under an emitter for exactly one minute. Multiply the millilitres collected by 0.0159 to get GPH, or by 0.06 to get L/h. A 1 GPH emitter should collect about 63 ml a minute. Test emitters near the start, middle and end of each line. Big differences point to pressure loss or clogging. For a more formal check, see measuring uniformity in drip irrigation.
Working pressure
Static pressure at the faucet doesn’t tell you what the emitters see. A gauge fitted at the end of a line, with the zone running, shows working pressure after the regulator, filter, friction and elevation. If it’s well below the emitters’ rated range, the line is probably too long or carrying too much flow.
Common sizing mistakes
- Adding emitters without adding up the flow. Each emitter seems tiny, but 150 of them at 2 GPH is 300 GPH, more than a 1/2-inch line is usually rated for.
- Sizing from the bucket test with no margin. Real working flow is lower than open-faucet flow.
- Mixing plant types in one zone. This forces you to overwater some plants or underwater others.
- Ignoring filtration. Undersized or missing filters lead to clogging that looks like a sizing problem. Our guide to choosing a drip irrigation filter covers mesh sizes.
- Treating ET-based numbers as exact. They’re starting estimates. Check soil moisture and adjust.
Quick answers
How many litres per hour is drip irrigation? It depends on the emitter. Common household emitters deliver about 2, 4 or 8 L/h each, and inline dripline is often in the 1.5–4 L/h range per emitter. A system’s total is the sum of all its emitters.
How many GPM do I need for drip irrigation? Add up your emitter flow in GPH and divide by 60. A zone of 120 GPH needs 2 GPM. Many home faucets supply several GPM, so drip zones are usually limited by tubing capacity and plant grouping more than by supply.
What is the formula for calculating flow rate? For a bucket test, flow = volume ÷ time. For a drip zone, flow = number of emitters × flow per emitter.
How deep should drip irrigation be? Most home drip lines sit on the surface under mulch. Inline dripline can be buried shallowly where the product is rated for it, but buried lines are harder to inspect and repair.
To see how the parts of a system fit together before you size it, start with how drip irrigation works.