What a venturi injector does
A venturi injector is a simple device that draws liquid fertilizer from a tank into irrigation water, a practice called fertigation. It has no moving parts and needs no electricity. It uses the water flowing through it to create suction. That makes it a common, affordable choice for small farms, greenhouses and larger home systems.
Several manufacturers make venturi injectors, including Jain Irrigation and many others, in sizes from about 1/2 inch up to a few inches. They work on the same principle, but suction rates, required pressure difference and flow ranges vary by model. The manufacturer’s performance chart for your specific model is the reference to use.
How a venturi injector works
Inside the injector, water passes through a narrowing section (a cone or throat). As the passage narrows, the water speeds up and its pressure drops. If the pressure in the throat falls below atmospheric pressure, it pulls liquid up a suction tube from an open tank and mixes it into the stream. The water then slows down and recovers some, but not all, of its pressure as it leaves.
Will a venturi work on your system?
The key requirement is a pressure difference. The pressure at the injector’s outlet must be noticeably lower than at its inlet before suction starts. Manufacturers’ charts typically show suction beginning only once the outlet pressure is some way below the inlet. It’s often in the region of 20% or more, and more for full suction. Check the chart for your model.
That has three practical consequences:
- You lose pressure. Your system must have enough supply pressure to spare after the injector for your filter, regulator and emitters. On a mains supply with plenty of pressure this is often fine. On a low-pressure or gravity system it may not be. See drip irrigation operating pressure.
- Flow through the injector must suit its size. Too little flow and there won’t be enough velocity to create suction. Compare your zone flow (from how to size a drip irrigation system) with the injector’s rated range.
- The suction rate changes with pressure. If supply pressure fluctuates, so does the amount of fertilizer drawn in.
Choosing a size and model
- Match the injector to your zone flow and available pressure using the manufacturer’s chart. It usually lists suction rate against inlet and outlet pressure.
- Larger injectors draw more fertilizer but need more flow to operate. An oversized injector on a small drip zone may not create suction at all.
- If you plan a bypass installation (below), the injector only needs to handle part of the flow, so a smaller unit can serve a larger main line.
Installation layouts
Bypass installation
The most common layout puts the injector on a bypass loop beside a section of main line:
- A tee before and after a valve on the main line feeds the bypass.
- The injector sits in the bypass, with shut-off valves on each side.
- The valve on the main line between the two tees is partly closed to create the pressure difference that drives water through the injector.
The bypass makes adjustment easy and lets you take the injector out of service by closing its valves and fully opening the main valve. Some systems use a small booster pump to drive the injector instead of throttling the main line. That’s mostly found in larger installations.
Placement relative to filter, regulator and backflow device
- Backflow protection comes first, between the water supply and the injection point (see Safety below).
- Inject upstream of the main filter where practical, so undissolved particles or precipitates are caught before reaching emitters. Our guide to choosing a drip irrigation filter covers filter types.
- Keep the injector where pressure is still high enough to drive it, which usually means ahead of any drip pressure regulator.
Suction line details
- Fit a strainer or foot filter on the suction tube in the tank.
- Use a check valve on the suction line so water can’t flow back into the fertilizer tank.
- Some injectors accept a small metering valve or flow meter on the suction line to fine-tune the rate.
- Keep the tank as close to the injector as practical and avoid long, uphill suction lines.
Measuring and setting the injection rate
Even with a chart, it’s worth measuring what your setup actually draws:
- Fill the fertilizer tank with plain water to a marked level.
- Run the zone with the injector operating for a set time, such as 10 minutes.
- Measure how much water was drawn from the tank.
- Divide by the time to get the suction rate (for example, litres or gallons per minute).
From that, and your zone flow, you can work out the dilution ratio. Then you can set how strong to mix the stock solution so the plants receive the fertilizer amount the product label recommends. Re-check after any change to pressure or zone layout.
A basic fertigation routine
A common sequence for each fertigation cycle:
- Wet first: run plain water until the whole zone is filled and at operating pressure.
- Inject: open the injector and draw in the planned amount of stock solution.
- Flush: keep running plain water long enough to push all the fertilizer out of the lines and emitters. Fertilizer residue left in lines can feed algae and bacteria, and deposits can clog emitters.
Injecting during the middle part of an irrigation cycle, rather than at the very end, keeps nutrients in the root zone rather than at the edge of the wetted area.
Fertilizer choices and clogging risks
- Use fertilizers sold as fully water-soluble or formulated for fertigation.
- Some combinations form solids when mixed at concentration. A well-known example is calcium-containing fertilizers with phosphates or sulfates. Keep incompatible products in separate tanks or inject them at different times, and follow the manufacturer’s guidance.
- Try a jar test: mix your planned stock solution, at the same strength and in a sample of your irrigation water, in a clear jar. Look for cloudiness or settling before you inject.
- Organic liquid fertilizers can encourage biological growth in lines and may contain particles. Check filtration needs and flush thoroughly.
- Hard water or high-iron water can react with some fertilizers. Water testing helps.
Safety and backflow
Injecting fertilizer means chemicals are in your irrigation line, so preventing them from flowing back into the water supply is critical.
- Local plumbing codes typically require a specific type of backflow prevention assembly when chemicals are injected into a system connected to drinking water. Often this is a reduced-pressure-principle (RP) assembly. Check with your water provider or local code official before installing.
- A simple hose-thread vacuum breaker or check valve may not be sufficient for chemical injection.
- Follow the fertilizer label for handling, protective equipment and storage. Keep stock tanks covered and labeled, and out of reach of children and pets.
Venturi vs. other injectors
| Injector type | How it works | Main pros | Main cons |
|---|---|---|---|
| Venturi | Water flow creates suction | Inexpensive, no moving parts, no power needed | Costs pressure; injection rate varies with pressure and flow |
| Batch (bypass) tank | Some water flows through a closed tank of fertilizer | Very simple | Concentration starts high and falls over time |
| Water-powered proportional injector | Water drives a piston that doses a fixed ratio | Steady ratio across a range of flows | Higher cost; needs maintenance |
| Electric metering pump | Pump injects at a set rate | Precise control | Needs power and controls; highest cost |
For many home and small-farm drip systems with good supply pressure, a venturi is a reasonable, low-cost option, as long as you calibrate it and protect the water supply. For how fertigation fits into the bigger picture of drip performance, see what is the efficiency of drip irrigation.