A garden well or borehole can supply irrigation water without metered bills or hosepipe-ban worries. Making it work well takes three things: knowing what’s in the water, a pump and pressure setup sized to both the well and the irrigation, and filtration that keeps drippers and nozzles clear. This guide covers each in turn.
Is well water good for gardens?
Often, yes. Many wells provide water that plants grow well on. Groundwater varies a lot from place to place, though. Some wells carry sediment, iron, manganese, high mineral hardness or salts. These can block irrigation equipment, stain paths and walls, or harm sensitive plants over time. Water used on food crops also needs to be reasonably free of harmful bacteria and contaminants. A water test is the starting point.
Test the water first
Ask a laboratory, your local authority or a water testing service for an irrigation-focused test. Useful measurements include:
| Test | Why it matters |
|---|---|
| Iron and manganese | Cause orange or black slime and deposits that block drippers, and stain surfaces |
| Hardness (calcium, magnesium) and pH | Scale can build up in emitters, especially with high pH |
| Salinity (electrical conductivity) and sodium | High levels can harm plants and soil structure over time |
| Sediment or turbidity | Sand and silt wear pumps and block filters |
| Bacteria (e.g., coliforms) and nitrates | Important if water touches vegetables eaten raw |
| Sulphur (hydrogen sulphide) | Rotten-egg smell. Some bacteria associated with it can form slime |
Retest every few years, or after floods or noticeable changes in taste, colour or smell.
How much water can your well supply?
The well’s yield, how fast it can be pumped without running dry, sets the upper limit for irrigation. If records from the well driller exist, start there. Otherwise:
- Run the pump at a steady flow into a container of known size and time it, to measure flow.
- Watch whether flow and pressure hold steady over a longer run, perhaps an hour, or whether the well draws down and output falls.
Plan irrigation to use less than the sustained yield. Pumping a well dry can damage some pumps and stir up sediment.
Choosing a pump
| Pump type | How it works | Typical use |
|---|---|---|
| Shallow-well jet pump (above ground) | Sucks water up by suction | Wells where the water level is fairly close to the surface. Suction lift is physically limited, typically to around 7–8 m in practice at best |
| Deep-well jet pump | Uses an ejector down the well to help lift water | Somewhat deeper wells. Less common now than submersibles |
| Submersible pump | Sits in the well below the water level and pushes water up | Deeper boreholes; generally efficient and quiet |
| Surface centrifugal pump | Above ground, often drawing from a dug well, pond or tank | Shallow sources, rainwater tanks |
| Solar pump | DC pump driven by solar panels, sometimes with a battery | Off-grid sites, allotments, remote plots |
Choose a pump that can deliver the flow your largest irrigation zone needs, at the pressure your emitters or sprinklers need, after allowing for lift from the water level and friction in the pipes. Pump makers publish performance curves showing flow against total head. A supplier or well contractor can match a pump to your well and system.
Electrical work for pumps should meet local regulations. Outdoor and borehole pumps generally need appropriate protection, and in many cases a qualified electrician.
Pressure tanks and switches
Most domestic well systems use a pressure tank and a pressure switch. The pump runs until the system reaches a set cut-out pressure, then stops. The tank supplies water until pressure falls to the cut-in point, and then the pump restarts.
Why it matters for irrigation:
- Short-cycling (the pump switching on and off rapidly) wears out pumps. It happens when an irrigation zone draws a little less than the pump delivers, or the tank is too small or has lost its air charge.
- Size zones so the pump runs continuously while a zone is on, or use a variable-speed / constant-pressure pump controller that adjusts output to match demand.
- Check the tank’s air pressure periodically, following the manufacturer’s instructions.
Filtration for drip and sprinklers
Well water usually needs more filtration than mains water:
- Sand separator (if the well produces sand): spins out heavier particles before they reach the filters.
- Screen or disc filter: catches fine sediment. Drip systems commonly need a fine filter, often in the range of 120–200 mesh. Use the rating your emitter manufacturer recommends.
- Pressure regulator for drip zones, as with mains water.
Clean filters regularly. Well systems can block a filter much faster than mains water, especially early in the season.
Dealing with iron and hard water
Iron is one of the most common problems for well-fed drip systems. When iron-rich groundwater meets air, it oxidises and forms deposits. Iron bacteria can also create slime that blocks emitters.
Options include:
- Use sprinklers or larger-bore outlets rather than fine drippers on very iron-rich water.
- Aeration and settling: pump into a tank, let the iron oxidise and settle, then draw cleaner water off the top for irrigation.
- Dedicated iron filtration: systems designed to remove iron before the water reaches the irrigation.
- Regular flushing of drip lines by opening the end caps.
- Line treatments such as acid or chlorine injection are sometimes used in agriculture to manage scale and bacterial slime. These involve chemicals and backflow risks, so get professional advice before trying them.
For hard water, flushing, pressure-compensating self-flushing emitters and occasional replacement of scaled emitters all help.
Designing zones around the pump
Size each irrigation zone so its total flow sits comfortably within what the pump can deliver at the required pressure, and within the well’s sustained yield. If you have a drip zone that uses little water, a constant-pressure pump controller or a larger tank helps avoid short-cycling. Our guide to dividing your garden into irrigation zones explains the flow calculations. Irrigation system components covers what goes after the pump.
Legal and safety considerations
- Abstraction rules. In England, taking more than 20 cubic metres of water a day from a well or borehole generally requires an abstraction licence from the Environment Agency. Small garden use is usually below that threshold, but rules differ in Scotland, Wales and Northern Ireland. In the US, groundwater rights and well permits vary by state. Check before drilling or heavily increasing use.
- No cross-connections with the mains. A well system must not connect directly to the public water supply. If you top up a tank from the mains, use an air gap. See do you need a backflow preventer for garden irrigation.
- Wellhead protection. Keep the well cap sealed to stop surface water, fertiliser and animals getting in.
- Food crops. If tests show bacterial contamination, keep the water off the edible parts of crops, or treat it, and get local advice.
Maintenance and winter care
- Clean filters regularly, more often at the start of the season.
- Check pressure tank air charge and switch settings as the manufacturer recommends.
- Flush drip lines periodically, especially on iron-rich water.
- In frost-prone areas, drain above-ground pumps, tanks and exposed pipes, or protect them with insulation, before freezing weather.
- Watch for changes in pump run time or pressure, which can signal a falling water level or a failing pump.
For how a well fits alongside other water sources in your plans, see planning a garden irrigation system. For a lower-tech alternative, see building a PVC rainwater harvesting system.