Planning and System Types

Irrigation System Components: The Parts Every Setup Needs

A plain guide to garden irrigation parts in the order water flows: tap connector, backflow device, timer, filter, pressure regulator, tubing, emitters and heads.

On this page
  1. The basic components of any irrigation system
  2. Garden system parts, in the order water flows
  3. Components by system type
  4. A mini irrigation system parts list for one raised bed
  5. Main components of an automatic system
  6. Sizing and compatibility tips

Every irrigation system, from a farm canal network to a drip kit on a balcony, does the same five jobs. It takes water from a source, controls when it flows, keeps it clean, carries it to where it’s needed, and applies it to the soil. Garden systems just do these jobs with smaller parts. Knowing what each part does makes it much easier to pick a kit, extend one, or work out why something isn’t working.

The basic components of any irrigation system

When people ask about the “five basic components,” they usually mean these functions:

  1. Source: a tap, tank, water butt, well or pump.
  2. Control: valves, timers or controllers that start and stop the flow.
  3. Conditioning: filters, pressure regulators and backflow protection.
  4. Conveyance: pipes and tubing that carry water across the garden.
  5. Application: emitters, porous hose or sprinkler heads that deliver it to the plants.

Large agricultural schemes add intake structures and drainage. At garden scale, the list below covers it.

Garden system parts, in the order water flows

Water source and connector

For most people, this is an outdoor tap. You’ll need a connector that matches the tap thread. Thread standards differ by country: UK taps generally use BSP threads, while North America uses garden hose thread (GHT), and the two aren’t interchangeable. On water butts, you’ll usually connect to the butt’s own tap or outlet. See connecting an irrigation system to an outdoor tap.

Backflow preventer

This is a check valve or vacuum breaker that stops garden water being siphoned back into the drinking supply. Many newer outdoor taps have one built in. If yours doesn’t, add one at the tap. Some systems need a higher level of protection under local rules. See do you need a backflow preventer for garden irrigation.

Timer or controller

  • Tap timers are battery-powered and screw onto the tap. They suit one or two zones.
  • Controllers run solenoid valves for several zones and often support rain or soil moisture sensors.

Filter

A screen or disc filter catches grit, scale and debris before they reach small emitters. It’s essential for drip and micro systems and useful for sprinklers too. Filters are rated by mesh. Drip kits commonly use a fine mesh, often around 120–150, but follow the emitter manufacturer’s recommendation. Clean the filter regularly, because a blocked filter starves the whole system.

Pressure regulator

Drip tubing and fittings are usually designed for much lower pressure than the mains supplies. A regulator reduces the pressure to the range your parts are rated for, which keeps fittings from popping off and evens out emitter output. Sprinkler systems often have pressure-regulated heads instead.

Mainline or supply tubing

  • Drip and micro systems: flexible polyethylene (LDPE) tube, commonly 13–16 mm (around 1/2 inch) for the main runs, with 4–6 mm micro tube branching off.
  • Sprinkler systems: larger polyethylene or PVC pipe, usually buried.

Diameters vary between brands, so check that tubing and fittings match before you buy.

Fittings

Tees, elbows, couplers, end caps, tap adaptors and grommets. Drip fittings are usually barbed or compression, while sprinkler pipe uses compression, crimp or glued joints. A hole punch is needed to insert emitters into drip tube, and goof plugs seal holes in the wrong place.

Distribution and application

This is where the water actually reaches the plants:

  • Drip emitters: point-source drippers with a set flow rate. Pressure-compensating types keep output steady along long runs or slopes.
  • Inline dripline: tube with emitters built in at fixed spacing.
  • Soaker or leaky hose: porous hose that seeps along its length.
  • Micro-sprinklers and sprayers: small heads on stakes.
  • Sprinkler heads: sprays, rotary nozzles and rotors. See the different types of irrigation sprinkler heads.
  • Bubblers: heads that flood a small basin, often used for trees.

End closures and flush points

Every drip run needs an end cap or a figure-8 end closure. Being able to open the ends lets you flush out sediment, which is one of the simplest ways to prevent clogging.

Valves (for multi-zone systems)

Manual ball valves or automatic solenoid valves divide the system into zones so each one gets enough flow. See how to divide your garden into irrigation zones.

Components by system type

Component Drip Soaker/leaky hose Pop-up sprinklers
Backflow protection Yes Yes Yes (often a higher grade)
Timer/controller Tap timer or controller Tap timer Controller with valves
Filter Essential Recommended Recommended
Pressure regulator Essential on mains Usually needed Pressure-regulated heads or regulator
Supply pipe 13–16 mm LDPE Standard hose to the bed Buried PE or PVC
Applicator Emitters/dripline Porous hose Spray heads/rotors
Valves Optional Optional Yes

A mini irrigation system parts list for one raised bed

For a single raised bed of about 1.2 × 2.4 m on a mains tap, a simple setup might need:

  • Tap connector and a backflow device, if the tap doesn’t have one built in
  • A battery tap timer
  • An inline filter
  • A pressure regulator matched to your tubing
  • A few metres of 13–16 mm supply tube from the tap to the bed
  • Enough inline dripline to run 3–4 rows across the bed
  • Tees or elbows to link the rows, plus end caps
  • Ground stakes to hold the line down

Many starter kits bundle most of this. If you’re planning a bigger build, DIY garden irrigation covers layout and assembly.

Main components of an automatic system

An automatic system is the parts above plus something that decides when to water. That might be a timer on a fixed schedule, a controller that runs zones in sequence, or a “smart” controller that adjusts from weather data or soil moisture readings. Sensors that skip a cycle after rain can stop a lot of unnecessary watering.

Sizing and compatibility tips

  • Stick to one brand or one tube size where you can. “13 mm” and “16 mm” tubing from different makers don’t always fit the same fittings.
  • Match total emitter flow to your supply. Add up the flow of everything that runs at once and compare it with your measured tap flow. Our garden irrigation planning guide explains the bucket test.
  • Keep runs within the manufacturer’s limits. Long runs lose pressure, so the last emitters drip less.
  • Use UV-stable tubing outdoors, or cover it with mulch.
  • Put the filter before the regulator unless the manufacturer says otherwise. Most kits are arranged this way.

The complete guide to planning and system types

Planning a Garden Irrigation System: How to Choose the Right Setup
Read the guide

Keep exploring

Guides from other topics

All topics →