A floppy irrigation system is a permanent overhead sprinkler system that uses “floppy” sprinklers. Each one has a short, flexible tube that flaps rapidly as water passes through it, scattering the water over a circle. There are no gears, springs or bearings in the head. The system was developed in South Africa and is mainly used on farms, orchards, nurseries and sports fields rather than in small gardens. This guide explains how it works, where it fits, and the main steps in designing one.
What is a floppy irrigation system?
Floppy systems are a type of solid-set sprinkler irrigation. The pipework and sprinklers stay in place permanently rather than being moved around the field. Laterals, usually buried, feed vertical risers. Each riser has a floppy sprinkler on top, and the sprinklers are spaced in a grid so their patterns overlap.
The defining feature is the sprinkler head. Instead of a rotating arm (like an impact sprinkler) or a gear drive (like a rotor), it uses the movement of a flexible tube to spread the water.
How a floppy sprinkler works
Water flows up the riser and into a short tube made of flexible material, such as silicone, held at the top. As water rushes through, the tube whips and oscillates rapidly in all directions. That movement breaks the jet into droplets and throws them out in a roughly circular pattern. The nozzle size and the operating pressure control how much water comes out and how far it travels.
Because the only moving part is the tube itself, there’s less to wear out or jam than in a sprinkler with internal mechanisms. Manufacturers generally present this as a lower-maintenance option.
Where floppy systems are used
Typical uses include:
- Field crops and vegetables on larger farms
- Orchards and vineyards, often with tall risers above the canopy
- Nurseries and turf farms
- Sports fields and large grassed areas
- Dust suppression on sites such as mines and stockpiles
Floppy sprinklers are sometimes discussed for frost protection or crop cooling, which are uses of overhead irrigation generally. Whether a particular system suits that job depends on the manufacturer’s specifications and local advice.
Advantages and limitations
Advantages often cited:
- Few moving parts, so less mechanical wear.
- Permanent installation, so there are no pipes to move between irrigations, which saves labour.
- Automation: zones can be run by valves and a controller.
- Flexible layouts, with risers of different heights for different crops.
Limitations:
- High up-front cost. A permanent grid of buried pipe and risers is a significant investment.
- Wind and evaporation. Like all overhead irrigation, it loses some water to drift and evaporation, and it wets the foliage.
- Obstructions. Fixed risers in a field can get in the way of machinery.
- Less precise than drip. For row crops and trees where water efficiency matters most, drip is generally more efficient. See types of irrigation systems for the comparison.
How to design a floppy irrigation system
A floppy layout follows the same logic as any solid-set sprinkler design. Exact spacing, nozzle choice and pressure must come from the manufacturer’s performance charts. The steps below are the general sequence.
1. Establish the water supply
- Available flow, from a borehole, dam, river or mains, measured in cubic metres or litres per hour.
- Available pressure at the field, after friction losses in the pipework.
- Water quality. Sediment and algae affect filtration needs. See using well water for garden irrigation for testing basics.
The supply sets how many sprinklers can run at once and therefore how many zones you’ll need.
2. Work out crop water needs and application rate
Decide how much water the crop needs per week in the driest period and how many hours per week you can irrigate. The sprinkler grid must apply water no faster than the soil can absorb it. Heavy clay soils need lower application rates than sandy ones to avoid runoff.
3. Choose layout and spacing
Sprinklers are usually laid out in a square or triangular grid. Spacing is chosen from the manufacturer’s tables for a given nozzle and pressure, so that patterns overlap enough to give even coverage. Windy sites generally need closer spacing. Our article on sprinkler head spacing explains the overlap principle with garden sprinklers. The idea is the same, at a larger scale.
4. Size the laterals, sub-mains and risers
- Laterals carry water along each row of sprinklers. They’re sized so the pressure difference between the first and last sprinkler stays within acceptable limits.
- Risers are set to a height that clears the crop at its tallest, plus whatever the manufacturer recommends.
- Sub-mains and the mainline carry water from the source to the zone valves.
Pipe sizing calculations (friction loss against flow) are normally done with manufacturer software or by an irrigation designer.
5. Divide into zones and plan control
Group sprinklers into zones that the supply can run at full pressure. Each zone gets a valve. A controller then runs the zones in sequence. The logic matches dividing a garden into irrigation zones, with bigger numbers.
6. Add filtration, drainage and backflow protection
- A filter suited to the water source and nozzle size.
- Drain valves at low points, especially where pipes could freeze.
- Backflow protection where the system connects to a potable supply, as local regulations require. See do you need a backflow preventer.
Is floppy irrigation worth it for a garden or smallholding?
For a typical home garden, usually not. Pop-up sprays or rotors handle lawns, and drip handles beds and borders more efficiently and at lower cost. See what are the different types of irrigation sprinkler heads.
A floppy system starts to make sense on larger areas, such as a paddock, a market garden or an orchard, where a permanent overhead system saves labour and a suitable water supply is available. Get a design from a supplier or irrigation designer before you buy, as most of the cost is in pipework that’s hard to change later.
Floppy vs flood irrigation (not the same thing)
Search results sometimes mix the two up. Flood irrigation is a surface method: water flows across the ground by gravity, with no sprinklers involved. Floppy irrigation is a pressurised overhead sprinkler method. They have very different costs, efficiency and uses. For more on surface methods, see what is the least efficient irrigation system.