Subsurface and Buried Watering

Subsurface Drip Irrigation: Components and Installation

Learn the basic components of a subsurface drip irrigation system and how to install one step by step, from filters and dripline to flushing and testing.

On this page
  1. What Subsurface Drip Irrigation Is
  2. The Basic Components of a Subsurface Drip System
  3. Planning Before You Dig
  4. How to Install a Subsurface Drip System, Step by Step
  5. Converting an Existing Sprinkler Zone to Subsurface Drip
  6. Running and Maintaining the System
  7. Common Installation Mistakes
  8. Frequently Asked Questions

What Subsurface Drip Irrigation Is

Subsurface drip irrigation (often shortened to SDI) is drip irrigation with the tubing buried. Instead of laying dripline on top of the soil or under mulch, you place it a few inches below the surface, where its built-in emitters release water straight into the root zone.

The basic idea is the same as surface drip: deliver small amounts of water slowly, close to the roots. Burying the line adds a few benefits. The surface stays drier, less water evaporates, nothing is visible, and the tubing is protected from sunlight, foot traffic and string trimmers. It also brings trade-offs. You can’t see when something goes wrong, and roots, soil and rodents can all get at the line. We cover those in detail in our article on the disadvantages of subsurface drip irrigation.

Home gardeners mostly use SDI under lawns, in shrub and perennial beds, in vegetable beds that aren’t deeply tilled, and along narrow strips where sprinklers would overspray onto paving or walls. Farms use the same principle on a much larger scale, usually with deeper lines and more elaborate filtration.

The Basic Components of a Subsurface Drip System

A subsurface system uses most of the same parts as a surface drip system. A few parts that are optional on the surface become close to essential once the line is buried. Here they are in the order water passes through them.

Water Connection and Backflow Prevention

The system starts where it connects to your water supply. That could be a tap into the main line, an existing irrigation valve manifold, or a hose bib for a small zone. A backflow preventer stops irrigation water, which can carry soil, fertilizer and bacteria, from being drawn back into your drinking water. Which type is required, and whether it has to be tested, depends on local plumbing codes. Check with your water utility or building department before you buy one.

Zone Valve and Controller

An automatic zone valve, wired to an irrigation controller (timer), turns the zone on and off. Because subsurface drip applies water slowly and doesn’t wet the surface, run it as its own zone. Don’t share a valve with spray heads or rotors. Their flow rates and run times are completely different.

Filter

Filtration matters more for subsurface drip than for almost any other kind of irrigation. Emitter passages are tiny, and a buried emitter that clogs is hard to find and fix. Most systems use a screen or disc filter. Many dripline makers call for roughly 120-mesh filtration (about 125 microns) or finer, but follow the specification for the product you buy. Put the filter where you can reach it easily, because you’ll be cleaning it regularly.

Pressure Regulator

Household water pressure is often higher than dripline is designed to handle. A pressure regulator brings it down to the dripline’s operating range. Landscape drip regulators are commonly sold in the 25–40 psi range. Many valve manufacturers also sell combined valve, filter and regulator assemblies (often called control zone kits), which keeps the head of the system tidy.

Supply Header

The supply header is a solid pipe, usually PVC or poly, that runs along one end of the area and feeds every dripline lateral. Laterals come off the header at regular intervals, a bit like the rungs of a ladder.

Dripline With Built-In Emitters

Dripline is tubing with emitters already moulded inside at fixed spacings, often 12 inches for landscape use. For buried installations, look for:

  • Pressure-compensating (PC) emitters, which deliver close to the same flow along the whole run and on slopes.
  • Root-intrusion protection. Some subsurface dripline uses copper or a root-inhibiting compound in the emitter to discourage roots from growing into the outlets. Rain Bird’s XFS line with Copper Shield is one example of this type of product.
  • Check valves (anti-drain) on some lines, which help keep the tubing full between cycles. This reduces the drain-out and suction that can pull soil into emitters.

For seasonal vegetable rows, some gardeners use thin-walled drip tape. It’s cheaper but less durable, and better suited to shallow, short-term burial than to permanent landscape installations.

Flush Header and Flush Valve

At the far end of the laterals, a second pipe called the flush header connects their ends together. It leads to a flush valve or a capped flush point. With both headers in place, the system becomes a closed loop or grid. Water reaches emitters from both directions, which evens out pressure. More importantly, opening the flush point lets you push sediment out of the whole system. Without a flush header, fine particles that slip past the filter tend to settle at the dead ends of the laterals.

Air/Vacuum Relief Valve

When a buried zone shuts off, water draining out of the lines can create a slight vacuum. The vacuum can suck muddy water and soil back in through the emitters. An air/vacuum relief valve, installed at the highest point of the zone (usually on the supply or flush header), lets air in as the system drains and lets trapped air out when it fills. This small, inexpensive part is one of the most commonly skipped, and skipping it causes real problems underground.

Helpful Extras

Component What it does Needed?
Pressure gauge or test port Lets you confirm operating pressure and spot leaks or clogs over time Strongly recommended
Flow meter Shows a rising flow (leak) or falling flow (clogging) Useful on larger systems
Valve boxes Protect and give access to the filter, flush valve and air relief valve Recommended
Operation indicator A small pop-up that shows the zone is pressurised, since you can’t see buried emitters Nice to have
Soil moisture sensor Helps adjust run times without guesswork Nice to have
Fertilizer injector Feeds nutrients through the system Mainly for vegetable or farm use

Planning Before You Dig

A few hours of planning prevents most subsurface drip failures.

Measure your flow and pressure. Time how long it takes to fill a bucket of known size at a tap near the system (for flow), and use a pressure gauge on a hose bib (for static pressure). Together, these tell you how much dripline one zone can run. Dripline manufacturers publish maximum lateral lengths and flow per 100 feet of line. Use those tables to size each zone.

Know your soil. Water spreads sideways farther in clay and loam than in sand, where it tends to move straight down. Sandy soils usually need closer line spacing and sometimes closer emitter spacing. Clay soils can take wider spacing but need slower, gentler watering to avoid saturation.

Choose the depth. Depth depends on what you’re growing and how you use the area: shallow under beds, a little deeper under lawns, deeper still for tilled farm rows. Our guide on how deep subsurface drip line should be buried covers the common ranges and the reasons behind them. For turf in particular, see subsurface drip irrigation for lawns.

Group plants into zones. Lawn, shrubs and vegetables have different water needs, and areas in sun and shade dry at different rates. Separate zones let you schedule each one properly.

Locate utilities. In the US, call 811 (or use your state’s online request) a few days before digging so underground utilities get marked. Other countries have similar services.

Draw a plan. Sketch the area to scale. Mark the head assembly, supply header, flush header, lateral spacing and the high point where the air relief valve will go.

How to Install a Subsurface Drip System, Step by Step

These steps describe a typical residential grid layout. Always check them against the installation guide for the dripline you’re using, because spacing, depth and maximum run lengths vary by product.

  1. Mark the layout. Use marking paint or flags to show where the headers and each lateral will go. Laterals usually run parallel to each other at a consistent spacing, often somewhere between about 12 and 24 inches depending on soil and plant type. Keep the outer lines a few inches in from edges and paving so the border doesn’t dry out.

  2. Install the head assembly. Connect the backflow preventer (if it isn’t already part of your main irrigation system), zone valve, filter and pressure regulator, in that order, downstream of your water source. Put the filter and regulator in a valve box.

  3. Trench for the headers. Dig trenches along both ends of the area for the supply header and the flush header. Lay the header pipe and add tees or fittings at the planned lateral spacing.

  4. Place the laterals. In open ground such as a new bed or a lawn before sod goes down, you can cut shallow trenches or loosen and remove soil to the target depth, then lay the dripline. Under existing turf, a vibratory plow or a dripline insertion tool can pull the line in with less disturbance. Keep lines straight and evenly spaced. Avoid sharp bends that could kink the tubing.

  5. Connect laterals to both headers. Attach each lateral to the supply header at one end and the flush header at the other, using fittings made for your dripline size (insert or compression fittings are common). Make sure every connection is fully seated. A loose fitting underground means digging it all up again.

  6. Add the air/vacuum relief valve and flush point. Install the air relief valve at the highest point in the zone, and the flush valve or flush cap at the lowest point of the flush header if possible. Give both a small valve box so you can get to them later.

  7. Flush before backfilling. Open the flush point and run the zone until the water comes out clear. This clears soil and plastic shavings that got in during installation.

  8. Pressure-test and inspect. Close the flush point and run the zone. Walk every line and fitting looking for leaks. If you have a gauge, check that pressure at the far end of the system is within the dripline’s operating range.

  9. Backfill carefully. Backfill by hand around fittings and tubing. Remove sharp stones, and gently firm the soil without crushing the line. Water the backfill lightly to help it settle.

  10. Map what you built. Before the line disappears for good, take photos and measure the position of headers, laterals and valve boxes from fixed points like the house or a fence. Keep the drawing with your irrigation records. You’ll need it the first time you plant a tree or install a fence post.

Converting an Existing Sprinkler Zone to Subsurface Drip

If you already have an in-ground sprinkler system, you can often convert one zone to drip rather than starting from scratch. The general approach:

  • Pick a zone that serves only beds, or only the area you want to convert. Avoid mixing drip and spray heads on one valve.
  • At the valve, or at the point where the zone’s pipe enters the area, add a filter and pressure regulator. Valve manufacturers sell retrofit kits for this.
  • Cap off the spray heads you’re no longer using. Retrofit kits that thread into an existing riser can be used to start a drip line.
  • Make sure the zone’s existing valve and backflow protection are in good working order.

Spray heads use far more water per minute than dripline, so you’ll need to completely reprogram that zone’s run times. A schedule written for spray heads will be wrong for drip.

Running and Maintaining the System

Buried systems ask for a few simple, regular habits:

  • Clean the filter on a schedule. How often depends on your water source: well and pond water usually need more frequent cleaning than municipal water.
  • Flush the laterals periodically by opening the flush valve until the water runs clear. Many guides suggest doing this at least a few times per season, and more often with dirty water.
  • Watch pressure and flow. A sudden drop in pressure or rise in flow suggests a leak or a cut line. A slow rise in pressure with falling flow can point to clogging.
  • Check the soil, not the surface. Since the surface stays relatively dry, use a soil probe or trowel to see how far moisture has spread. A moisture sensor can help too.
  • Adjust for seasons. Shorten run times in cool weather, lengthen them during hot spells, and pause the system after significant rain.
  • Prepare for frost where winters are hard. Buried dripline is less exposed than surface tubing, but the head assembly, filter and any above-ground parts may still need draining or protecting. Follow the manufacturer’s guidance for your climate.

Common Installation Mistakes

  • Skipping the air/vacuum relief valve. This invites soil into emitters every time the system shuts off.
  • Dead-end laterals with no flush header. Sediment builds up at the ends with no way out.
  • Undersized filtration or a filter buried where nobody will ever clean it.
  • Laterals longer than the manufacturer allows, which leaves the far ends underwatered.
  • Spacing that’s too wide for the soil, especially in sand, which shows up as stripes of dry soil or turf between lines.
  • No record of where the lines are. This makes every later digging project a risk to the system.

Frequently Asked Questions

What are the main parts of an irrigation system?

Most automatic irrigation systems share the same backbone: a water source, backflow prevention, a controller, zone valves, supply piping, and the emitters themselves (sprinkler heads, sprays, rotors or drip emitters). Drip and subsurface systems add a filter and a pressure regulator. Buried systems should also have flush points and an air/vacuum relief valve.

What is the most inefficient irrigation system?

There’s no single official ranking. In general, though, methods that put water on the surface in ways that let it evaporate, blow away or run off tend to be the least efficient. That includes flood or furrow irrigation on farms and, at home, hand-held hoses and spray sprinklers run in wind or heat or on slopes where water runs off. Drip, and especially subsurface drip, is usually considered among the more efficient options when it’s designed and maintained well. If you’re comparing methods, our article on the advantages of drip irrigation explains where those savings come from.

Are there low-tech alternatives to buried dripline?

Yes. For small gardens, buried clay pots and wicking beds water from below without any pumps, valves or filters. See our guides to olla irrigation and capillary irrigation and wicking systems.

Keep exploring

Guides from other topics

All topics →