Maintenance and Troubleshooting

How to Winterize a Drip Irrigation System

Protect drip irrigation from freeze damage: shut off water, store the timer, filter and regulator, drain or blow out lines at low pressure, and restart in spring.

On this page
  1. Do you need to winterize drip irrigation?
  2. What you’ll need
  3. Step-by-step winterization
  4. Hose-bib systems vs. permanent systems
  5. Can drip tubing stay outside all winter?
  6. Starting the system back up in spring

Water expands as it freezes. If it’s trapped in drip tubing, fittings, filters or valves, it can crack them and leave you with leaks in spring. Winterizing a drip system means getting the water out and protecting the parts most likely to break. For most home drip systems it’s a straightforward DIY job.

Do you need to winterize drip irrigation?

If your area gets hard freezes, yes. Flexible polyethylene drip tubing tolerates freezing better than rigid parts, but filters, pressure regulators, timers, backflow preventers and valves are vulnerable, and so are any rigid PVC pipes. Even tubing can be damaged if it’s full of water in a deep freeze.

In mild climates with only occasional light frosts, many gardeners leave drip systems in place and running through winter. Protect exposed hose-bib parts and timers on cold nights. Your local extension service can advise on what’s typical where you live.

What you’ll need

  • A bucket or tub for storing small components
  • Hose-thread plugs or caps for open connections
  • Foam pipe insulation, or insulating covers, for anything that stays outside
  • Optional: an air compressor with an adjustable regulator, for blowing out lines

Step-by-step winterization

1. Shut off the water

Turn off the tap or the valve that supplies the drip system. If the system is fed from a permanent supply line, also close the shutoff for that line, and drain the pipe between the shutoff and the outdoor parts if it’s exposed to freezing.

2. Remove and store the head assembly

The “head assembly” is the group of parts where the drip system connects to the water supply. It typically includes:

Unscrew these, drain them, and store them indoors somewhere frost-free, like a garage, basement or shed that stays above freezing. Clean the filter screen before you put it away so it’s ready for spring.

3. Open end caps and drain the lines

  1. Open the end caps, figure-8 ends or flush valves at the end of every line.
  2. If your system has low-point drain valves, open them.
  3. Walk the tubing and lift sections as you go, working water toward the open ends and low points.
  4. Let the lines drain fully.

Emitters themselves release some water, but don’t rely on them to empty the lines. Opened ends drain much faster.

4. Blow out lines with low-pressure air (optional)

If your layout has low spots that trap water, or the tubing is buried, compressed air can push out what draining leaves behind.

  • Keep the pressure low. Drip components are built for low pressure, and too much air can blow fittings apart or damage emitters. Figures around 20 to 30 psi are commonly cited for drip systems. Never exceed the rating of your lowest-rated component, and check your manufacturer’s guidance.
  • Connect the air to the start of the system, where the head assembly was, using a suitable adapter.
  • Open the end of one line at a time and run air until only mist comes out.
  • Never stand over open fittings or emitters while blowing out, and wear eye protection.

Systems with permanent valves and backflow devices may have specific blow-out requirements. Backflow devices in particular can be damaged by improper blow-out. If you aren’t sure, check the manufacturer’s instructions or use an irrigation professional.

5. Close up and protect open ends

Once the lines are drained:

  • Put a hose-thread plug or cap on the open supply connection to keep insects, soil and debris out.
  • Some gardeners leave end caps slightly loose so leftover moisture can escape. Others close them to keep debris out. Either way, make sure the water has drained first.

6. Protect anything that stays outside

If valves, a backflow preventer or rigid pipe have to stay outdoors, drain them as fully as you can and wrap them in foam pipe insulation or an insulated cover. Follow any instructions from the device’s manufacturer about leaving test cocks or drain valves in a particular position over winter.

Hose-bib systems vs. permanent systems

Hose-bib (tap) systems are the easiest. Remove the timer, backflow preventer, filter and regulator from the tap, drain the lines, and plug the start of the tubing. Also protect the outdoor tap itself, for example with an insulated faucet cover or by shutting off and draining the supply to it if your home has an indoor shutoff. Hose-end kits like the ones covered in our Hozelock watering system guide follow the same pattern.

Permanent systems connected to an irrigation valve manifold are more involved. You’ll need to shut off and drain the irrigation supply line, protect or drain the valves and backflow device, and set the controller to off or rain mode. If the drip zones share a system with sprinkler zones, the whole system is usually winterized together, often by blowing out with air.

Can drip tubing stay outside all winter?

Usually, yes. Polyethylene drip tubing is commonly left in the garden over winter once it’s drained, and it holds up reasonably well. Thin micro tubing and emitters can become brittle with age and sun exposure, so inspect them in spring. Bring in the head assembly and timer, which are the most freeze-sensitive parts.

If you’d rather roll up surface tubing and store it, label which line goes where to make spring setup easier.

Starting the system back up in spring

  1. Wait until the risk of hard freezes has passed.
  2. Reinstall the backflow preventer, filter, pressure regulator and timer. Put fresh batteries in the timer.
  3. With the line ends open, turn the water on slowly and flush until it runs clear.
  4. Close the ends and run the system. Walk each line, checking for leaks, cracked fittings and emitters that aren’t dripping.
  5. Clean or replace any blocked emitters.

Our drip irrigation maintenance guide covers flushing, clog prevention and how to deal with scaled emitters through the season.

The complete guide to maintenance and troubleshooting

Drip Irrigation Maintenance: Flushing, Acid Treatment and Clog Prevention
Read the guide

Keep exploring

Guides from other topics

All topics →