Short answer
The Hozelock Select is a dial-style water controller that fits between your outdoor tap and your hose or watering system. To use it, fit fresh batteries, screw it onto the tap, connect your hose or drip system, choose how often to water and how long each watering should last, then leave the tap turned on. The controller opens and closes its internal valve on the schedule you set.
Hozelock has made several versions of its controllers over the years, and the exact dials, buttons and battery type vary. Treat the steps below as a general guide and check them against the instruction leaflet for your unit.
Before you start
You’ll need:
- The controller and its tap connector (or a suitable one for your tap thread)
- Fresh batteries of the type stated in your manual
- Your hose or micro-irrigation system with a click-fit connector
Decide roughly what time of day you want watering to happen. Early morning or evening is usually best, because less water is lost to evaporation. On many simple dial controllers, the time you make the setting matters (more on that below).
Fit the batteries
- Open the battery compartment as shown in your manual.
- Insert fresh, good-quality batteries, matching the polarity markings.
- Close the compartment firmly so the seal keeps water out.
Weak batteries are behind many controller problems, so start each season with a fresh set.
Attach the controller to the tap and hose
- Screw the tap connector onto the tap, then attach the controller as described in its instructions. Hand-tight is normally enough. Overtightening can distort the washer and cause leaks.
- Connect your hose or watering system to the controller’s outlet using a click-fit hose connector.
- If you’re running drip parts, fit a pressure reducer and filter after the controller, as your drip kit recommends.
- Turn the tap on fully. The controller only manages the water the tap supplies, so the tap must stay on.
- Check for leaks at each joint.
If you’re building the watering system at the same time, our Hozelock watering system setup guide covers the layout from the tap to the drippers.
Set how often and how long to water
Dial controllers like the Select generally ask for two choices:
- Frequency: how often watering happens, for example once a day or twice a day, depending on the options your model offers.
- Duration: how many minutes each watering lasts.
Some practical starting points:
- Drip systems on beds and borders: less frequent, longer waterings encourage deeper roots.
- Containers and hanging baskets: often need more frequent watering in hot weather, because pots dry out quickly.
- Sprinklers on lawns: watering deeply and less often is usually better than a short daily sprinkle.
Check the soil a few days after you set the schedule. If it’s still soggy, cut back the duration or frequency. If plants are wilting or the soil is dry an inch or two down, increase it.
Understanding when watering starts
Dial-only controllers without a clock display often don’t let you type in a start time. Instead, the watering cycle is usually tied to the moment you make the setting or start the controller, and it repeats at the chosen frequency from then on. On these models, if you want watering at 7 a.m., you set it at about 7 a.m.
Check your manual to see how your version of the Select handles start times. If you set it at a convenient moment and find it watering at an odd hour, this is the most likely reason. Resetting it at the time you want watering to begin should fix it.
Removing the batteries or resetting the controller may clear the schedule, so you may need to set it again after a battery change.
Running a manual watering
Many Hozelock controllers have a manual or “water now” option for an extra watering without changing the schedule. How you start it depends on the model: it might be a button, or a dial position. If yours doesn’t have one, you can always take the controller off and connect the hose straight to the tap for hand watering.
Pausing or switching off
- For a short break (after heavy rain, for example), use the off or pause setting if your model has one, or simply turn the tap off.
- For longer periods, switch the controller off and turn off the tap. Remember to reset the schedule when you start again.
Troubleshooting the Select controller
It doesn’t water at all
- Make sure the tap is fully on.
- Replace the batteries.
- Check that a frequency and duration are both set, and the controller isn’t switched off.
- Look for a blocked filter washer at the controller inlet and rinse it clean.
It waters at the wrong time
- It was probably set at that time of day. Reset it at the time you want watering to start.
It won’t stop watering
- Replace the batteries. Low batteries can leave a valve unable to close properly on some timers.
- Check for debris in the inlet filter or valve.
- If it continues, turn off the tap and contact Hozelock or check the manual.
It leaks at the tap
- Check the washer in the tap connector and refit it squarely. Worn washers and O-rings are cheap to replace.
Weak flow from the watering system
- Clean the filters, check the line for leaks or kinks, and make sure you haven’t overloaded the system with too many drippers or sprayers.
Winter care
Water left inside a controller can freeze and damage it. Before the first frosts:
- Turn off the tap and remove the controller.
- Drain it, take out the batteries, and store it indoors somewhere dry.
- Drain and protect the rest of your watering system as well. Our guide to winterizing a drip irrigation system explains how.
Where to find the manual
Hozelock usually provides product manuals on its website. Search for “Select controller” or the product code printed on the unit or its packaging. Keep a copy handy, since it’s the most reliable source for your model’s specific dials and settings.