What a Micro Irrigation Kit Includes
“Micro irrigation” covers low-flow watering through small outlets: drippers that release a few litres or gallons per hour, and microjets or micro-sprinklers that spray a small area. Kits from various brands share the same basic parts:
- A master unit or head assembly at the tap, which reduces pressure and filters the water
- A main supply pipe, often 13 mm or 1/2-inch
- Thinner distribution pipe, such as 4.6 mm (3/16-inch) or 1/4-inch tubing, to reach individual plants
- Drippers, which can be inline, end-of-line or adjustable
- Microjets, spray nozzles or micro-sprinklers for wider coverage
- Connectors, tees, elbows, end caps, holders and stakes, plus a tool for making holes
Brands are rarely compatible with each other, so stay with one system or check pipe sizes carefully. For a Gardena-specific walkthrough, see Gardena drip system installation.
The Master Unit: Pressure Reducer and Filter
The master unit (some brands call it a start unit or head assembly) is the first part after the tap or timer. Its two jobs are to reduce household pressure to a level the micro parts are designed for, and to filter out particles that would clog small outlets.
For example, Gardena describes its Master Unit 1000 as reducing pressure to about 1.5 bar, with a flow capacity of about 1,000 litres per hour and a removable built-in filter. Other brands use different figures. The flow rating matters: it caps how many outlets you can run at once.
Never connect micro pipe directly to the tap without the master unit. At full household pressure, connectors can blow apart and drippers spray instead of drip.
Before You Start: Measure Your Flow
Do a bucket test: open the tap fully and time how long it takes to fill a bucket of known size. A 10-litre bucket filling in 30 seconds means 20 litres per minute, or about 1,200 litres per hour. The amount you can use is the lower of your tap’s flow and the master unit’s rated flow. Leave some headroom rather than planning to use all of it.
Installation Instructions, Step by Step
- Sketch the garden and mark which plants get drippers and which areas get sprays.
- Fit the master unit to the tap, after a timer if you use one, following the flow direction.
- Lay the main supply pipe along the beds. Warm it in the sun first if it’s stiff, and fix it with pipe holders or stakes.
- Cut and branch with tees and elbows to reach each bed or group of plants. Cut pipe squarely.
- Insert inline drippers directly into the main pipe where plants sit next to it, or run thinner distribution pipe to plants further away and fit end drippers.
- Add microjets or spray nozzles on stakes or risers where you need wider coverage.
- Flush with the pipe ends open until the water runs clean.
- Close the ends with end caps or closing plugs.
- Test the system, adjust spray directions and dripper flows, and fix any leaks.
- Set the timer and check soil moisture over the following days.
Designing a Microjet Layout
Spray Patterns and Radius
Microjets and micro-sprinklers come in full-circle (360°), half-circle (180°), quarter-circle (90°) and strip patterns. Many have adjustable flow or radius. Typical small garden sprays cover a radius of roughly 1 to 2 metres, but always check the product data.
- Use quarter and half patterns along edges, corners and paths, so water stays in the bed.
- Use full circles in the middle of larger areas.
- Use strip patterns for narrow beds.
Spacing and Overlap
For even coverage, space sprays so each one reaches, or nearly reaches, its neighbours. This is often called head-to-head spacing. A spray with a 1.5-metre radius would be placed about 1.5 metres from the next. Sprays spaced too far apart leave dry patches between them. Laying out a simple grid on paper first helps.
Don’t Mix Jets and Drippers Carelessly
A single microjet can use as much water as a dozen or more drippers, and it wets a wide area quickly, while drippers need longer run times. If both share one line on one timer schedule, either the dripper plants go short or the sprayed area is overwatered. Where possible, put sprays and drippers on separate lines or timer outlets.
Flow Budget Example
Suppose the master unit and tap allow up to about 1,000 litres per hour, and you plan:
- 60 drippers at 2 litres per hour = 120 L/h
- 8 microjets at about 40 litres per hour each = 320 L/h
The total of 440 L/h fits comfortably. Thirty microjets at the same rate would need 1,200 L/h, which is too much for one line. Flow figures here are examples; use the ratings for your actual parts. Long, thin distribution pipes also lose pressure, so check the kit maker’s maximum lengths and number of outlets per line.
How Long to Run Drippers and Microjets
- Drippers apply water slowly, so run times are longer, often 30 minutes to a couple of hours depending on flow, soil and plants.
- Microjets apply water much faster over a wider area, so runs are usually shorter.
The best check is the soil: dig down a few inches near a dripper and in a sprayed area a few hours after watering. Adjust until the root zone is moist but not waterlogged. Seasonal adjustment matters: summer may need much more than spring. For vegetable beds, how often to water a raised vegetable garden has a schedule by weather.
Disadvantages of Micro Irrigation
- Clogging: small outlets block easily without good filtration, especially with hard water or stored rainwater.
- Evaporation and drift: microjets lose more water to wind and sun than drippers, and can wet foliage.
- Damage: small parts are easily knocked, stepped on or chewed by animals.
- Planning: you need to budget flow and pressure, or the far end of the system will underperform.
- Monitoring: you can’t see water underground, so you need to check soil moisture.
Maintenance and Winter Storage
- Clean the master unit’s filter regularly.
- Flush lines at the start of each season and whenever flow drops.
- Check sprays for blocked nozzles and correct direction.
- Before frost, remove the master unit and timer, drain the pipes, and store parts somewhere frost-free.
For an overview of designing a complete system, see the home drip irrigation guide, and for choosing between emitter types, the best type of drip irrigation.