Home Drip Installation

Gardena Drip System Installation Guide

Step-by-step Gardena Micro-Drip-System installation: master unit, 13 mm and 4.6 mm pipes, drippers, sprays, timers, flow planning, winter storage and fixes.

On this page
  1. How the Gardena Micro-Drip-System Is Organised
  2. Main Components
  3. Plan Before You Buy
  4. Step-by-Step Installation
  5. Watering Pots, Balconies and Hanging Baskets
  6. Adding a Timer
  7. Maintenance and Winter Storage
  8. Troubleshooting
  9. Adding Gardena Drip to an Existing Sprinkler System

How the Gardena Micro-Drip-System Is Organised

Gardena’s Micro-Drip-System is a modular kit for watering beds, rows, hedges, pots and balcony planters. It follows the same logic as any drip system, with Gardena-specific parts:

  1. A master unit at the tap reduces water pressure and filters the water.
  2. A 13 mm (1/2-inch) connecting pipe carries water around the garden.
  3. Thinner 4.6 mm (3/16-inch) supply pipe branches off to individual plants and pots.
  4. Drippers, spray nozzles and drip irrigation line deliver the water.
  5. Connectors, holders and closing plugs join and finish the system.

Gardena’s parts are designed to work together. Mixing them with other brands’ pipe and fittings is risky, because pipe diameters and connector designs differ. Product names, ratings and available parts change over time, so treat the details below as a general guide and check the instructions that come with your parts.

Main Components

Component What it does
Master unit Fits at the tap (or after a timer); reduces pressure and filters the water. Gardena describes its Master Unit 1000 as reducing pressure to about 1.5 bar, with a flow of about 1,000 litres per hour and a removable filter
13 mm connecting pipe Main supply line through beds and along rows
4.6 mm supply pipe Thin branch pipe to individual plants, pots and baskets
Inline drippers Inserted into the 13 mm pipe where plants sit beside it
End drippers Fitted at the end of a 4.6 mm pipe for individual plants or pots
Adjustable or pressure-compensating drippers Let you set the flow, or keep it even along longer lines
Drip irrigation line Pipe with drippers built in at intervals, for rows, hedges and dense beds
Spray nozzles and micro-sprinklers Wider coverage for dense planting or small areas
T-pieces, L-pieces, couplings and closing plugs Branch, turn corners and seal pipe ends
Pipe holders and stakes Fix pipe and drippers in place

Gardena also sells start sets that bundle a master unit, pipe and drippers for common uses such as planted rows or plant pots. These are a convenient way to begin.

Plan Before You Buy

  1. Sketch the area and measure the distance from the tap to each bed, row or group of pots.
  2. Decide how each area will be watered: inline drippers or drip irrigation line for rows and beds, end drippers on 4.6 mm pipe for pots, sprays for dense planting.
  3. Add up the flow. Each dripper and spray has a flow rating in litres per hour. Total them and compare with the master unit’s rating and with your tap’s flow, measured by timing how long it takes to fill a bucket. Sprays use far more water than drippers.
  4. Check line limits. The manual gives the maximum pipe length and number of drippers per line. Longer runs or too many outlets leave the far end short of water.
  5. Group plants with similar needs on the same line, or plan separate lines on a multi-outlet timer.

Step-by-Step Installation

  1. Connect the master unit to the tap. If you use a water timer, it typically goes between the tap and the master unit. Follow the flow direction marked on the unit.
  2. Lay out the 13 mm pipe along the beds. Leaving it in the sun beforehand makes it more flexible and easier to straighten. Fix it with pipe holders at regular intervals.
  3. Cut the pipe cleanly and squarely with a pipe cutter or sharp secateurs wherever you need a T-piece, elbow or end.
  4. Fit the connectors. Gardena’s Quick & Easy connection technology is designed so pipes can be connected, extended and detached without special tools; follow the instructions for your connectors to make sure each joint is fully seated and secure.
  5. Insert inline drippers into the 13 mm pipe beside each plant, using the method or installation tool specified for your drippers.
  6. Run 4.6 mm supply pipe from the main line to plants or pots further away, and fit end drippers at the ends. Fix the drippers in the soil with holders or stakes.
  7. Add spray nozzles on risers or stakes where you need wider coverage.
  8. Flush the system: turn the water on with the pipe ends open until it runs clean, to clear out any debris.
  9. Close the ends with closing plugs or end caps.
  10. Test and adjust: run the system, check every dripper and spray, fix leaks, and adjust any adjustable drippers.

For general technique on making holes and fitting drippers in drip pipe, see how to install drip emitters.

Watering Pots, Balconies and Hanging Baskets

The 4.6 mm pipe is useful for containers. Run the 13 mm pipe along the back of a row of pots or along a balcony rail, then branch a short 4.6 mm pipe to each pot with an end dripper held in place with a stake. Large pots usually benefit from two drippers. Keep branches short and similar in length. See drip irrigation for balcony gardens and drip for hanging baskets for layout ideas.

Adding a Timer

A water timer is what makes the system low-maintenance. Gardena and other brands offer battery and app-controlled tap timers. Program a start time and duration, then adjust after checking soil moisture a few hours after a run. Drippers apply water slowly, so run times are longer than with sprinklers; containers in summer may need watering daily.

Maintenance and Winter Storage

  • Clean the master unit’s filter regularly; it can be removed for rinsing.
  • Flush the lines at the start of the season and whenever flow drops.
  • Check drippers for clogs and replace any that don’t respond to cleaning.
  • Before frost, remove the master unit and timer and store them somewhere frost-free, as Gardena advises for the master unit. Open the pipe ends to let water drain.

Troubleshooting

Problem Likely cause Fix
Connectors come apart Pipe not fully inserted or connector not tightened; no master unit Recut the pipe end, reseat it, make sure the master unit is fitted
Far drippers give little water Too many outlets or line too long; clogged filter Split into separate lines, clean the filter
Dripper not dripping Clog from grit or limescale Flush the line; clean or replace the dripper
Sprays weak Too many sprays on one line Move sprays to a separate line or timer outlet

Adding Gardena Drip to an Existing Sprinkler System

A Gardena Micro-Drip-System is designed to run from a tap through its own master unit. If you want to add drip to an in-ground sprinkler system, the drip area needs its own zone with filtration and pressure regulation, rather than sharing a valve with spray heads. Our guide to converting a sprinkler zone to drip explains how. For brand-neutral planning, see micro irrigation kit installation and the home drip irrigation guide.

The complete guide to home drip installation

Home Drip Irrigation: Planning and Installing a Garden Drip System
Read the guide

Keep exploring

Guides from other topics

All topics →